Appendices
68
© NXP Laboratories UK 2015
JN-UG-3093 v1.5
The table below summarises the key sequences and associated operations that can
be performed from the Remote Control Unit in the JenNet-IP Smart Home demo.
I = ON O = OFF + = UP - = DOWN # = PRG * = ALL GRP = A, B, C or D
Operation
Key Sequence
Switch on lights
in selected group
GRP ON
ALL ON
A/B/C/D I
* I
Switch off lights
in selected group
GRP OFF
ALL OFF
A/B/C/D O
* O
Increase brightness
of lights in selected group (increase occurs
while key UP [+] key is pressed). If a light is off, it is switched on.
GRP UP
ALL UP
A/B/C/D +
* +
Decrease brightness
of lights in selected group (decrease
occurs while key DOWN [-] key is pressed). If a light is off, com-
mand has no effect.
GRP DOWN
ALL DOWN
A/B/C/D -
* -
Add nodes
(within radio range) to the specified group (the radio
is put in a
low-power mode
for this operation)
PRG UP ON GRP/ALL
# + I A/B/C/D/*
Commission and then add nodes
(within radio range) to the
specified group as well as to the ‘All’ group.
PRG ON OFF ON GRP
# I O I A/B/C/D
Commission and then add nodes
(within radio range) to the
‘All’ group only
.
PRG ON OFF ON ALL
# I O I *
Remove nodes
(within radio range) from the specified group
(the radio is put in a
low-power mode
for this operation)
PRG DOWN OFF GRP/ALL
# - O A/B/C/D/*
Remove nodes
(within radio range) from the specified group.
PRG OFF ON OFF GRP
# O I O A/B/C/D
Remove nodes
(within radio range) from the
‘All’ group only
.
PRG OFF ON OFF ALL
# O I O *
Commission a Border-Router
(within radio range) to learn net-
work settings in extending standalone WPAN to full JIP system
PRG ON OFF ON OFF
# I O I O
Commission an additional Remote Control Unit
(within radio
range) to act as an
independent
Remote Control Unit for WPAN.
PRG ON OFF ON DOWN
# I O I -
Commission an additional Remote Control Unit
(within radio
range) to act as a
cloned
Remote Control Unit for WPAN.
PRG ON OFF ON UP
# I O I +
Try to join an existing WPAN
.
PRG UP DOWN UP
# + - +
Create a standalone WPAN
.
PRG DOWN UP DOWN
# - + -
Perform a factory reset
.
PRG OFF DOWN OFF
# O - O
Perform a software reset
.
PRG ON UP ON
# I + I
Table 10: Remote Control Key Sequences and Associated Operations
Note:
In normal operation, the Remote Control Unit
sleeps until it is needed. It should be woken by pressing
the Wake (blue circle) button before entering any of the
above command sequences on the keypad.
Содержание JN516x-EK001
