NXP Semiconductors AN10881 страница 101 Скачать руководство пользователя

Страница: 101 / 102

AN10881

All information provided in this document is subject to legal disclaimers.

Application note

Rev. 2 — 26 September 2011

101 of 102

continued >>

NXP Semiconductors

AN10881

TEA1713 resonant power supply control IC with PFC

7.4.1.1

Soft-start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

7.4.1.2

Soft-stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

7.4.2

SNSCURPFC open and short protection . . . . 40

7.5

PFC boost OverVoltage Protection (OVP) . . . 41

7.6

PFC mains UnderVoltage Protection
(brownout protection) . . . . . . . . . . . . . . . . . . . 41

7.6.1

Undervoltage or brownout protection level . . . 42

7.6.2

Discharging the mains input capacitor . . . . . . 42

7.6.3

SNSMAINS open pin detection . . . . . . . . . . . 43

HBC functions . . . . . . . . . . . . . . . . . . . . . . . . . 44

8.1

HBC UVP boost . . . . . . . . . . . . . . . . . . . . . . . 44

8.2

HBC switch control . . . . . . . . . . . . . . . . . . . . . 44

8.3

HBC adaptive non-overlap . . . . . . . . . . . . . . . 44

8.3.1

Inductive mode (normal operation) . . . . . . . . . 44

8.3.2

Capacitive mode . . . . . . . . . . . . . . . . . . . . . . . 46

8.3.3

Capacitive Mode Regulation (CMR) . . . . . . . . 47

8.4

HBC oscillator . . . . . . . . . . . . . . . . . . . . . . . . . 49

8.4.1

Presettings . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

8.4.2

Operational control . . . . . . . . . . . . . . . . . . . . . 49

8.4.3

CFMIN and RFMAX . . . . . . . . . . . . . . . . . . . . 50

8.4.3.1

Minimum frequency setting for CFMIN . . . . . . 50

8.4.3.2

Maximum frequency setting for RFMAX . . . . . 51

8.4.4

RFMAX and High Frequency Protection
(HFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

8.5

HBC feedback (SNSFB) . . . . . . . . . . . . . . . . . 52

8.5.1

HBC Open-Loop Protection (OLP) . . . . . . . . . 53

8.6

SSHBC/EN soft-start and enable . . . . . . . . . . 54

8.6.1

Switching ON and OFF using an external
control function . . . . . . . . . . . . . . . . . . . . . . . . 54

8.6.1.1

Switching ON and OFF using SSHBC/EN . . . 55

8.6.1.2

Hold and continue. . . . . . . . . . . . . . . . . . . . . . 55

8.6.2

Soft-start HBC. . . . . . . . . . . . . . . . . . . . . . . . . 55

8.6.2.1

Soft-start voltage levels . . . . . . . . . . . . . . . . . 56

8.6.2.2

SSHBC/EN charge and discharge . . . . . . . . . 56

8.6.2.3 SNSFB,

SSHBC/EN

and soft-start reset -

operating frequency control . . . . . . . . . . . . . . 58

8.6.2.4

Soft-start reset . . . . . . . . . . . . . . . . . . . . . . . . 58

8.7

HBC overcurrent protection and regulation . . 59

8.7.1

HBC overcurrent regulation . . . . . . . . . . . . . . 59

8.7.1.1

Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

8.7.2

HBC overcurrent protection . . . . . . . . . . . . . . 60

8.7.3

SNSCURHBC boost voltage compensation . . 60

8.7.4

Current measurement circuits. . . . . . . . . . . . . 61

8.7.5

SNSCURHBC layout . . . . . . . . . . . . . . . . . . . 61

Burst mode operation . . . . . . . . . . . . . . . . . . . 62

9.1

Burst mode controlled by SNSOUT . . . . . . . . 62

9.2

External comparator for Burst mode
implementation . . . . . . . . . . . . . . . . . . . . . . . . 63

9.3

Advantages of Burst mode for HBC . . . . . . . . 64

9.4

Advantages of Burst mode for HBC and PFC
simultaneously . . . . . . . . . . . . . . . . . . . . . . . . 65

9.5

Choice of burst level and hysteresis level . . . 66

9.6

Output power - operating frequency
characteristics . . . . . . . . . . . . . . . . . . . . . . . . 67

9.7

Lower SUPHS in burst . . . . . . . . . . . . . . . . . . 68

9.8

Audible noise . . . . . . . . . . . . . . . . . . . . . . . . . 68

9.8.1

Measurements in the resonant transformer
construction . . . . . . . . . . . . . . . . . . . . . . . . . . 68

9.8.2

Burst power-dependent noise level . . . . . . . . 69

9.9

PFC converter and resonant converter
simultaneous bursting . . . . . . . . . . . . . . . . . . 69

9.9.1

PFC output voltage variations . . . . . . . . . . . . 70

9.9.2

PFC burst duration. . . . . . . . . . . . . . . . . . . . . 70

9.9.3

Switching between burst and normal
operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

9.9.4

Audible noise during mode transition. . . . . . . 70

9.10

Design guidelines for Burst mode operation . 71

9.11

Enable/disable Burst mode . . . . . . . . . . . . . . 71

9.12

Unused Burst mode . . . . . . . . . . . . . . . . . . . . 71

Protection functions . . . . . . . . . . . . . . . . . . . . 72

10.1

Protection overview . . . . . . . . . . . . . . . . . . . . 72

10.2

IC protection. . . . . . . . . . . . . . . . . . . . . . . . . . 72

10.2.1

OverTemperature Protection (OTP) . . . . . . . . 72

10.2.2

Latched protection . . . . . . . . . . . . . . . . . . . . . 72

10.2.2.1 Resetting a latched protection shutdown

state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

10.3

SNSOUT protection . . . . . . . . . . . . . . . . . . . . 73

10.3.1

OverVoltage Protection (OVP) output . . . . . . 74

10.3.1.1  Auxiliary winding  . . . . . . . . . . . . . . . . . . . . . .   74
10.3.1.2  Principle of operation . . . . . . . . . . . . . . . . . . .   74
10.3.1.3  Connecting external measurement circuits  . .   74
10.3.2

UnderVoltage Protection (UVP) output . . . . . 74

10.3.2.1  Auxiliary winding  . . . . . . . . . . . . . . . . . . . . . .   74
10.3.2.2  Principle of operation . . . . . . . . . . . . . . . . . . .   74
10.3.2.3  Severe voltage drop . . . . . . . . . . . . . . . . . . . .   75
10.3.2.4  Connecting external measurement circuits  . .   75
10.3.3

OVP and UVP combinations . . . . . . . . . . . . . 75

10.3.3.1  Circuit configurations . . . . . . . . . . . . . . . . . . .   75
10.3.3.2  OVP functional and UVP disabled . . . . . . . . .   75
10.3.3.3  UVP functional and OVP disabled . . . . . . . . .   76
10.3.3.4  Both OVP and UVP disabled . . . . . . . . . . . . .   77
10.4

Protection timer . . . . . . . . . . . . . . . . . . . . . . . 78

10.4.1

Block diagram of the RCPROT function . . . . 78

10.4.2

RCPROT working as protection timer . . . . . . 78

10.4.3

RCPROT working as a restart timer. . . . . . . . 79

10.4.4

Dimensioning the timer function. . . . . . . . . . . 80

Miscellaneous advice and tips. . . . . . . . . . . . 81

11.1

PCB layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

11.1.1

General setup . . . . . . . . . . . . . . . . . . . . . . . . 81

Содержание AN10881







































































































Результаты поиска

Содержание AN10881

Отзывы:

Похожие инструкции для AN10881

Бренды по названию

Популярные бренды

NXP Semiconductors AN10881, Примечание к применению

Результаты поиска

Содержание AN10881

Отзывы:

Похожие инструкции для AN10881

Бренды по названию

Популярные бренды