NXP Semiconductors AN10881 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 102

NXP Semiconductors AN10881 Скачать руководство пользователя страница 40

AN10881

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2011. All rights reserved.

Application note

Rev. 2 — 26 September 2011

40 of 102

NXP Semiconductors

AN10881

TEA1713 resonant power supply control IC with PFC

7.4.1 PFC soft-start and soft-stop

The PFC has a soft-start function and a soft-stop function to prevent transformer
noise/rattle at start-up or during Burst mode operation. The soft-start slowly increases the
primary peak current at the start of operation. The soft-stop function slowly decreases the
transformer peak current before operation is stopped.

A resistor and a capacitor between SNSCURPFC and the current sense resistor
R

SENSE(PFC)

set both functions.

7.4.1.1

Soft-start

Before start of operation, an internal current source of 60



A charges the capacitor to

V

SNSCURPFC

= 60



A



R

SS

. When SNSCURPFC exceeds the internal start voltage of

0.5 V, the operation can start. Select a resistor R

SS



12 k



to ensure that the start

voltage level is reached. At start-up, the current source is stopped and the voltage on
SNSCURPFC drops as R

SS

discharges C

SS

. During this discharge the peak current of

each cycle increases until C

SS

is discharged completely and the normal peak current

regulation level (OCR/OCP), set by R

SENSE(PFC)

, is reached.

The soft-start period can be claclulated with

:

(14)

7.4.1.2

Soft-stop

Soft-stop is achieved by switching on the internal current source of 60



A again.

The current charges C

SS

and the increasing capacitor voltage reduces the peak current.

When SNSCURPFC reaches 0.5 V the operation is stopped.

The voltage is only measured during the off-time of the PFC power switch to prevent
measurement disturbances during soft-stop.

7.4.2 SNSCURPFC open and short protection

When the SNSCURPFC pin is open, SNSCURPFC is charged to 0.5 V by the internal

current source of 60



A for soft-start. The PFC does not start switching because of OCP.

When the SNSCURPFC pin is short circuit to ground, the PFC cannot start operation as
the start level of 0.5 V has not been reached.

Fig 20. PFC soft-start and soft-stop setup

001aal030

60

μ

Atyp

RSENSE(PFC)

RSS

≥

12 k

Ω

CSS

COMP

SNSCURPFC

0.5 V

CONTROL

4

TEA1713



R

SS

C

SS



=

«
...
38
39
40
41
42
...
»

Содержание AN10881







































































































Отзывы:

Нет отзывов