nVent.com | 45
Der Temperatursensor und mindestens
200 mm des Sensorkabels müssen von
der Dämmung bedeckt sein. Achten Sie
darauf, dass das Temperatur halteband
nicht zu nahe am Sensor verlegt
wird. Halten Sie einen Abstand von
mindestens 200 mm zum Sensor ein.
Das Kabel des KTY-Sensors kann
auf bis zu 100 m verlängert werden.
Das Verlängerungs-kabel muss eine
Basisisolierung von 500 V und einen
festen Leiterquerschnitt von mindestens
0,75 mm² (bei 100 m) aufweisen.
Bei Verwendung des Sensors PT100
muss eine Überbrückung eingebaut
werden (Abb. 4, Seite 45). Das Kabel
des optionalen Sensors PT100 darf 200
mm nicht überschreiten. Dabei ist auf
die richtige Polarität zu achten.
2.3.5. Anschluss der Alarmkontakte
Der im Inneren des Temperaturstellers
vorhandene Alarmkontakt kann
für das Schalten einer externen
Alarm-Vorrichtung verwendet werden. Im Falle eines Alarms wird
dieser normalerweise geschlossene Kontakt geöffnet. Innerhalb
eines Netzwerks müssen alle Alarmkontakte in Serie verdrahtet
sein. Der Alarmanschluss, (siehe Abb. 4) befindet sich in der oberen
rechten Ecke des Temperaturstellers und ist mit “alarm contact”
gekennzeichnet. Drücken Sie für den Anschluss einer Ader die seitlich
der Anschlussklemme angebrachte orangefarbene Lasche mit einem
Schraubendreher nach unten, führen Sie den Draht in die Öffnung ein,
und geben Sie die Lasche wieder frei. Die für den Alarmanschluss
verwendete Leitung muss eine Isolationsspannungsfestigkeit von 500 V
aufweisen. Siehe Kapitel 4 für die Alarmrelaisbedingungen.
Anmerkung: Bei der Master-/Slave-Kombination mit Alarmfunktion
müssen die Alarme mit einem geschirmten RS485-Kabel in Reihe
geschaltet werden. Z.Bsp. MONI-RS-485 Wire
2.3.6. Netzwerk
Siehe Kapitel 5.5.1., Abb.
B
. Der HWAT-ECO-Temperatursteller kann in
einem System mit bis zu 9 Temperaturstellern verwendet werden. Alle
Temperatursteller müssen untereinander über die Eingänge A und B
parallel an der Anschlussklemme (siehe Abb. 4) elektrisch verbunden
sein. Dies setzt voraus, dass mehrere Adern an einer Anschlussklemme
angeschlossen werden müssen.
Alarmkontakte
Standard-Temperaturfühler (KTY)
Brücke
bei
Pt100
Pt100 (2-Leitertechnik)
BA
BMS
TEMP
BA
BMS
TEMP
NC
NO
C
Abb. 4
Anschlüsse im
HWAT-ECO.
Содержание Raychem HWAT-ECO V4
