11
GB
COMPONENTS AND CONTROLS (PIC. 1)
1
2
3
4
Pad
5
Switch ON/OFF
Lock-off button
Speed button
Woolen wheel
SAFETY INSTRUCTIONS FOR POLISHERS
BEFORE USE:
• Check the functioning of the tool before each use and, in
case of a defect, have it repaired immediately by a qualified
person; never open the tool yourself
• Inspect tool cord and plug before each use and, if damaged,
have them replaced by a qualified person
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• Inspect the extension cord periodically and replace it, if
damaged
• Use the tool and its accessories in accordance with this
instruction manual and in the manner intended for the tool;
use of the tool for operations, different from those normally
expected to be performed by the tool, could result in a
hazardous situation
• This tool should not be used by people under the age of
16 years
• This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the tool
by a person responsible for their safety
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
• Be sure tool is switched off when plugging in.
DURING USE:
• Handle the tool with care
- wear protective gloves and use safety glasses
- do not leave the tool unattended
- never use the tool in the proximity of inflammable gases
or combustible materials (risk of explosion)
• Prevent electrical shock
- ensure the tool does not get wet
- do not use the tool in damp locations
- when used outdoors, connect the tool via a fault current
(FI) circuit breaker with a triggering current of 30 mA
maximum, and only use an extension cord
which is intended for outdoor use
• Handle the cord with care
- keep the cord away from heat, oil and sharp edges
- do not carry the tool by the cord, and do not yank the cord
to disconnect it from the socket
- do not suspend the tool by the cord
• Never use the tool in conjunction with chemical solvents
• Make sure work area is adequately ventilated
• Keep work area clean and well lit
• Keep children away from work area
• Ensure that children do not play with the tool
• Stay alert; watch what you are doing, use common sense
and do not operate the tool when you are tired
• Take a secure stance; do not overreach, especially on
ladders and stages
• Ensure that the tool is switched off, before putting it aside
• In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
AFTER USE:
• Switch off the tool and disconnect the plug
• Do not store/leave the tool outdoors
• Store the tool in a dry and locked-up place, out of reach
of children
USE
• On/off switch (1)
! check if switch is off before plugging in
- switch on the tool by pushing switch
- switch off the tool by pushing switch
•Lock-off button (2)
- operate continuously by pushing the lock-off button
•Speed button (3)
-adjust speed by turning the speed button
•Pad (disc) (4)
-the connection of the pad is M14; Standard diameter for
our machine is 180mm; It can be changed accordingly;
•Woolen wheel (5)
-the material can be changed to be sponge accordingly
MAINTENANCE / SERVICE
• Always keep tool and cord clean
! disconnect the plug before cleaning
• Never use easy inflammable liquids for cleaning the
polisher in general
• If the tool should fail despite the care taken in manufactu-
ring and testing procedures, repair should be carried out by
an after-sales service centre
- send the tool un-dismantled together with proof of purchase
to your dealer
ENVIRONMENT
• Do not dispose of electric tools, accessories and packaging
together with household waste material (only for EU countries)
- in observance of European Directive 2002/96/EC on waste
of electric and electronic equipment and its implementation in
accordance with national law, electric tools that have reached
the end of their life must be collected separately and returned
to an environmentally compatible recycling facility
- symbol & will remind you of this when the need for disposing
occurs
TECHNICAL SPECIFICATION
V
oltage
230V
-
50Hz
Motor
No load
speed
-1
Disc
size
180 mm
1200
W
600-3300
min
