background image

®

INSTALLATION INSTRUCTIONS

SELECTIVE CALL INTERCOM SYSTEM

MODEL: IM-5000 MASTER STATION

This booklet contains information for wiring and installing

the master station. All system wiring and remote station
rough-in frames should be installed before mounting and
connecting the master station.

Detailed information on wiring and mounting system

components (i.e. speakers, remote controls, etc.) are
packaged with each separate component.

IM-5000 SERIES REPRESENTATIVE WIRING ILLUSTRATION

Use this diagram for reference only

NUTONE CHIME
TRANSFORMER

PUSH

BUTTON

120vAC, 60Hz

HOUSE POWER

18/2 (NUTONE S-143)

OPTIONAL

NUTONE

ELECTRONIC
DOOR CHIME

SEE CHIME

INSTALLATION

INSTRUCTIONS

200' MAX

NUTONE IW-2

300' MAX

S-143

SHIELDED

AUDIO

CABLES

OPTIONAL

MUSICAL

SOURCE

PUSHBUTTON FOR

OPTIONAL CHIME

MODULES

(UP TO 3 DOOR RUNS)

EARTH

GROUND

NUTONE S-143

(18/2) MAX 50'

USE 14/2 FOR RUN

BETWEEN 50-125' 

14

GA

NUTONE IW-6

TO ADDITIONAL

REMOTE SPEAKER

STATION

14/2 WITH

GROUND

CAUTION: DO NOT SUPPLY POWER

UNTIL LOW VOLTAGE POWER

CONNECTIONS ARE MADE IN

MASTER, 120vAC, 60H

Z

, CLASS 1

OBSERVE LOCAL CODE. UL LISTED

CLASS 2 NUTONE MODEL 401T

TRANSFORMER MUST BE USED

TRANSFORMER

SUPPLIED WITH

MASTER

ROUGH-IN

FRAME

SECONDARY

24v, 40vA

INTERCOM MASTER

NUTONE

IW-2

IW-6

DOOR SPEAKER
RECESS MODEL

MOUNTS IN

HOUSING OR

SURFACE MOUNTS

PATIO SPEAKER

W/CONTROLS.

INSTALLS IN

FRAME.

18/2

300' MAX

DOOR SPEAKER MODELS WITH

CHIME PUSHBUTTON ALSO

REQUIRE 18/2 (S-143) TO CHIME

LOCATION OR TO MASTER IF

OPTIONAL CHIME MODULE IS USED

INSIDE 5" SP.

W/CONTROL

ANGLED

DESKTOP

FRAME

IW-6

8' 6 COND. CABLE

AND CONNECTOR

WALL

RECEPTACLE

INSIDE 8" SP.

W/O

CONTROLS.

INSTALLS IN

FRAME.

INSIDE 5" SP.
W/CONTROL.

ANGLED

SURFACE

MOUNT

FRAME

INSIDE 5" SP.
W/CONTROL.

INSTALLS IN

FRAME.

OUTSIDE 8"

SP. W/O

CONTROLS.

INSTALLS IN

FRAME.

OUTSIDE 8"

SP. W/O

CONTROLS.

INSTALLS IN

FRAME.

INSIDE 8" SP.
W/CONTROL.

INSTALLS IN

FRAME

INSIDE REMOTE

CONTROL.

INSTALLS IN

FRAME.

OUTSIDE

REMOTE

CONTROL.

INSTALLS IN

FRAME.

OUTSIDE

REMOTE

CONTROL.

INSTALLS IN

FRAME.

IW-6

IW-6

IW-2

25'

MAX

IW-2

IW-2

25'

MAX

25'

MAX

IW-6

IW-6

IW-6

IW-6

MAXIMUM OF 750' RUN.

MAXIMUM OF 4000'

TOTAL WIRE.

IW-6

MAX 3 CABLES

TO ONE SPEAKER

Содержание IM-5000 series













Отзывы: