background image

Installation / Operation / Maintenance 

 

  

NRD USA / 2937 Alt Boulevard / PO Box 310 / Grand Island, NY 14072-0310

 

  PHONE

 716 773 7634 / 

FAX

 716 773 7744 / 

EMAIL

 [email protected] / 

WEB

 www.nrdllc.com 

 

  NRD Asia Pte. Ltd

 / 114 Lavender Street #08-90 CT Hub 2 Singapore 338729 

  PHONE

 +65 6679 1707 / 

EMAIL

 [email protected]

WEB 

www.nrdllc.com

 

 

                                                                                                                                INSTNeutralizerAC – 1/19 

The Neutralizer

AC Ionizing Blow Gun is de-

signed with a replaceable air filter.  NRD recom-
mends replacing the air filter every three months.  
The air filter may need to be replaced more often 
depending on amount of use.  Additional replace-
ment air filters are available by contacting NRD. 

 

 

 

Replace filter media as follows: 

 

1.

 

Remove the back cap of the Neutralizer

AC 

Ionizing Blow Gun, by turning it counter-
clockwise. 

2.

 

Remove filter media and screen. 

3.

 

Place screen and new filter media in back 
cavity. 

4.

 

Attach the back cap to the Neutralizer

AC 

Ionizing Blow Gun. Cap to be hand tight, do 
not over tighten.

 

 
Note: If the air directional cylinder falls out during 
the filter change, put the cylinder back in with the 
arrow for air flow pointing toward the front of the 
blow gun.

 

 
Trouble Shooting Guide 

 

Symptom 

Probable Cause 

Corrective Action 

 

LED is not lighting 

 

Battery does not have sufficient 
charge. 

 

Recharge battery. 

 

Static charges are not 
eliminated 

 

Emitter pin is old or degraded. 

 

Ions generated are being recom-
bined before they reach the 
charged surface 

 

Replace emitter pin 

 

The Neutralizer

AC air nozzle 

needs to be closer to the charged 
surface 

 

Air flow is reduced 

 

Supply line filter(s) are plugged 

 

Neutralizer

AC air filter is 

plugged 

 

Air supply pressure is low

 

 

Replace supply line filter(s) 

 

Replace Neutralizer

AC air filter 

 

Increase air supply pressure

 

 

Battery is not charging 

 

Battery charger is not recogniz-
ing the presence of a battery. 

 

Unplug battery charger from AC 
power source for a few seconds, 
this will “Reset” the charger. 

 

NOTE: If you are having a problem other than listed above or the corrective action is not correcting 
the problem contact NRD for further assistance. 

 
 

Device disposal

 

 

 

 

The Neutralizer

®

AC device should not be placed in household waste bins.  

Please check local regulations for information about the disposal of electronic 
products in your area.

 

 

 

 

 

 Back cap 

Screen 

Air filter 

Содержание NeutralizerAC 6500








Отзывы: