background image

N1050 Controller 

NOVUS AUTOMATION 

8/8 

0002 

MV 

Read: Output Power in  automatic or 

manual mode. 

Write: Not allowed. See address 28. 

Range: 0 to 1000 (0.0 to 100.0 %). 

IDENTIFICATION 

N1050

 

A

 

B

 

A:

  Available Outputs: 

PR

:   OUT1= Pulse / OUT2= Relay 

PRRR

:  OUT1= Pulse / OUT2= OUT3= OUT4= Relay 

B:

  Serial Communication: 

(Blank)

  (basic version, without serial communication); 

485

      

(RS-485 serial version, Modbus protocol) 

C:

  Power Supply: 

(Blank):

 .................................................................Model standard 

 .......................................... 100~240 Vac / 48~240 Vdc; 50~60 Hz 

24 V

: ............................................................................ Model 24 V  

 ........................................................................ 12~24 Vdc / 24 Vac  

SPECIFICATIONS 

DIMENSIONS

: .......................................... 48 x 48 x 80 mm (1/16 DIN) 

Cut out the panel: ..............................  46 x 46 mm (+0.5 -0.0 mm) 
Approximate Weight: .............................................................. 75 g 

POWER SUPPLY

  Model Standard:  .....................100 to 240 Vac (±10 %), 50/60 Hz 
   

 ......................................  48 to 240 Vdc (±10 %)  

  Model 24 V: .......................  12 a 24 Vcc / 24 Vca (-10 % / +20 %) 
  Maximum Consumption: ........................................................  6 VA 

ENVIRONMENTAL CONDITIONS

Operation Temperature: ...............................................  0 to 50 °C 
Relative Humidity: ................................................... 80 % @ 30 °C 
For temperatures above 30 °C, reduce 3 % for each °C. 
Internal use; Category of installation II, Degree of pollution 2;  

Altitude < 2000 meters. 

INPUT:

 ........................... 

J

K

T, S

 and 

Pt100

 (according of 

Table 01

)

 

Internal Resolution: ...................................... 32767 levels (15 bits) 
Resolution of Display: ......... 12000 levels (from -1999 up to 9999) 
Rate of input reading: .................................... up 10 per second (*) 
Accuracy:  ....... Thermocouples 

J

K

T

: 0.25 % of the 

span

 

±

1 °C 

 .................................. Thermocouple 

S:

 0,25 % of the 

span

 

±

3 °C  

 ................................................................ 

Pt100

: 0,2 % of the 

span 

Input Impedance: .................. Pt100 and thermocouples: > 10 M

 

Measurement of Pt100: .......................... 3-wire type (

α

=0,00385) 

With compensation for cable length, excitation current of 0.170 mA. 
(*) Value adopted when the Digital Filter parameter is set to 0 

(zero) value. For Digital Filter values other than 0, the Input 

Reading Rate value is 5 samples per second. 

OUTPUTS: 

OUT1: .................................................. Voltage pulse, 5 V / 25 mA 
OUT2: ................................ Relay SPST; 1,5 A / 240 Vac / 30 Vdc 
OUT3: ................................ Relay SPST; 1,5 A / 240 Vac / 30 Vdc 
OUT4: ...................................Relay SPDT; 3 A / 240 Vac / 30 Vdc 

FRONT PANEL

:

 

 ......................... IP65, Polycarbonate (PC) UL94 V-2

 

HOUSING

: .................................................... IP20, ABS+PC UL94 V-0 

SPECIFIC CONNECTIONS FOR TYPE FORK TERMINALS. 
DISPLAY: 

LCD type, alphanumeric with 11 segments.

 

PROGRAMMABLE CYCLE OF PWM: 

from 0.5 up 100 seconds;

 

STARTS UP OPERATION: 

after 3 seconds connected to the power 

supply.

 

CERTIFICATION: UL CE 

 

WARRANTY 

Warranty conditions are available on our website 

www.novusautomation.com/warranty

 

Содержание N1050









Отзывы: