manualshive.com logo in svg

NOVUM 555QE, Руководство по обслуживанию, Страница: 19 / 20

Поделиться
Скачать
NOVUM 555QE Скачать руководство пользователя страница 19

GHE-1207 Service Manual 

19 

 

17. Auto Buttonhole adjustment 

Problem 1:

 buttonhole presser foot is not sensed when you select button pattern and pull buttonhole lever 

down. 

Solution:

   

1. Open face cover 

2. Loosen the screw of buttonhole switch case (128024), then adjust and move the switch case backward, 

tighten screw and test. 

Check: 

1. Select buttonhole pattern 

2. 

Pull do   utto hole le er  hile the sig  of le er does ’t flash o  the L

ED display. 

3. Start to sew complete                    buttonhole               

 

Problem 2. 

The shape of buttonhole is sew like

               

, this situation is BH switch is backward too far. 

Solution:

 Loosen the screw of buttonhole switch case (128024), then adjust and move the switch case 

forward, tighten screw and test.

 

 

Check: 

Select buttonhole pattern 

2. Pull down buttonhole 

le er  hile the sig  of le er does ’t flash o  the LCD display.

 

3. Start to sew complete                    buttonhole 

 

 

 

 

 

 

 

BH switch case 

(128024) 

Содержание 555QE





















Отзывы:

Нет отзывов