Novexx Solutions ALX 73 Series Скачать руководство пользователя страница 8

Страница: 8 / 15

Operating manual ALX 73x | file version 00 | 04/2011

Printhead |

LEANING

ALX

73x

8. The resistance of the new printhead can be entered

using the

SYSTEM PARAMETER > Head resistance

pa-

rameter.



The resistance is given on the printhead sticker

[12 B].

Testing the printhead

The printer is equipped with a test function that checks
the functionality of each single dot.

Dot check with status report



Open

SERVICE FUNCTION > Head dot test

A status report is generated after the dot check to pro-
vide information about the number and position of any
dots that may be faulty.

Dot check with display message



Press the apply + feed keys.

Message indicating a faulty dot:



If all dots are fault-free, no message appears.



If an error message occurs, the current print job is

stopped.

Duration of the dot check

The entire check can last from 10 s to several minutes
depending on the printhead (the wider the printhead
and the more defective dots, the longer the duration) of
the check.

Interrupting the dot check



Press the feed+cut+online keys.



To cancel the dot check in situations where it is ab-

solutely necessary, reset the unit!

CAUTION!

Entering the wrong resistance can damage
the printhead!



Enter the resistance that is applied

against the

installed

printhead.

Status: 5103

Dot defective

CAUTION!

Danger of destroying individual dots on the
printhead.



Never quit a dot check by turning off the

unit!

[12] Printhead (A) with resistance identification (B), in this case:

1221 Ohm.

Содержание ALX 73 Series
















Результаты поиска

Содержание ALX 73 Series

Отзывы:

Похожие инструкции для ALX 73 Series

Бренды по названию

Популярные бренды

Novexx Solutions ALX 73 Series, Руководство по эксплуатации

Результаты поиска

Содержание ALX 73 Series

Отзывы:

Похожие инструкции для ALX 73 Series

Бренды по названию

Популярные бренды