Novexx Solutions ALX 73 Series Скачать руководство пользователя страница 2

Страница: 2 / 15

Operating manual ALX 73x | file version 00 | 04/2011

Cleaning instructions |

LEANING

ALX

73x

Cleaning instructions

Safety

Cleaning agents

Cleaning interval



Clean machine regularly.

The frequency depends on the following factors:

•

Operating conditions

•

Daily operating duration

•

Label material/ribbon combination used

WARNING!

Dangerous situations may arise during maintenance and cleaning work. Accidents
may occur due to mechanical or electrical effects if the relevant safety instructions
are not observed!



Switch off the device before cleaning or maintenance and pull out the mains

power connecting line!



Never allow liquid to get into the machine!



Do not spray the machine with spray bottles or sprays! Use a cloth wetted with

cleaning agent.



Repairs to the machine must only be made by trained service technicians!

CAUTION!

Sharp cleaning materials may damage the printer.



Do not use any cleaning agents or materials that could damage or destroy the

paint finish, labelling, display, type plates, electrical component, etc.



Do not use any scouring cleaning agents or any cleaning agents that could dis-

solve plastic.



Do not use acid or alkaline solutions.

Part to be cleaned

Cleaning agent

Order No.

Printhead

Cleaning stylus

95327

Cleaning paper

5030

Rubber rollers (print roller,
pressure roller, etc.)

Roller cleaner

98925

Deviator rollers

Cleaning solvent, alcohol, isopropyl
alcohol

Label release spray

90073

Housing

Standard commercial neutral
cleaning agent

[tab. 1]

Recommended cleaning agents:

Содержание ALX 73 Series
















Результаты поиска

Содержание ALX 73 Series

Отзывы:

Похожие инструкции для ALX 73 Series

Бренды по названию

Популярные бренды

Novexx Solutions ALX 73 Series, Руководство по эксплуатации

Результаты поиска

Содержание ALX 73 Series

Отзывы:

Похожие инструкции для ALX 73 Series

Бренды по названию

Популярные бренды