Novexx Solutions ALX 73 Series Скачать руководство пользователя страница 15

Страница: 15 / 15

| Replacing the filter liner

Operating manual ALX 73x | file version 00 | 04/2011

LEANING

ALX

73x

Replacing the filter liner

The replacement interval for the filter liner must be de-
fined according to the specific circumstances. The fol-
lowing factors determine the frequency:

•

Dust content of the air

•

Operating duration

The following error message appears in case of over-
heating:

The filter liner can be cleaned by blowing it out with
compressed air or by washing it out.

To change the filter liner:

1. Push the locking hook [23A] up with a screwdriver.

At the same time remove the fan cover [24A].

2. Replace the filter liner [24B] with a new or cleaned

filter liner (item number: A9752).

3. Press the fan cover in place again.

CAUTION!

A clogged dust filter can result in overheating,
thereby causing a machine failure.



Replace the filter liner on the fan regularly.

Status num: 5026

MotorProtect CPU

[23] Locking hook (A) on the fan cover.

[24] Remove the fan cover (A).

Содержание ALX 73 Series
















Результаты поиска

Содержание ALX 73 Series

Отзывы:

Похожие инструкции для ALX 73 Series

Бренды по названию

Популярные бренды

Novexx Solutions ALX 73 Series, Руководство по эксплуатации

Результаты поиска

Содержание ALX 73 Series

Отзывы:

Похожие инструкции для ALX 73 Series

Бренды по названию

Популярные бренды