Novexx Solutions ALX 73 Series Скачать руководство пользователя страница 5

Страница: 5 / 15

| Printhead

Operating manual ALX 73x | file version 00 | 04/2011

LEANING

ALX

73x

Cleaning the printhead

Paper dust and coloured particles from the thermal
transfer ribbon may collect on the printhead during
printing. Over time, this can significantly impair the
printing quality in the following ways:

•

Contrast differences in label

•

Bright strips in printing direction

Cleaning interval

•

Thermal transfer print: every time the ribbon roll is
changed

•

Thermal direct print: every time the label roll is
changed

Preparing the printhead

1. Switch off the machine.

2. Unplug the mains power connecting line.

3. Remove the label material and ribbon.

4. Remove both wing bolts [3A] until the printhead can

be swivelled up.



Before swivelling the printhead up, shift it about

1 cm towards the middle of the axle.



If the printhead is not at the limit stop on the

side, mark the position on the axle in advance.

5. Rotate the printhead up [4].

WARNING!

Burn hazard! The printhead can become hot
during operation.



Be careful whenever touching the printer.

[3]

Loosen the wing bolts (A) on the printhead.

[4]

Rotate the printhead up.

Содержание ALX 73 Series
















Результаты поиска

Содержание ALX 73 Series

Отзывы:

Похожие инструкции для ALX 73 Series

Бренды по названию

Популярные бренды

Novexx Solutions ALX 73 Series, Руководство по эксплуатации

Результаты поиска

Содержание ALX 73 Series

Отзывы:

Похожие инструкции для ALX 73 Series

Бренды по названию

Популярные бренды