Novell NETWARE 6 Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 152

Novell NETWARE 6 Скачать руководство пользователя страница 131

Troubleshooting

131

Internetwork Packet Exchange

103-000176-001

August 29, 2001

Novell Confidential

Manual

99a

38

July 17, 2001

card on each router. One of the routers you should start with is the
next-hop router. Repeat these steps until you find the destination
network number. If you do not find a duplicate network number in
either direction, check each link in the path for errors.

NLSP Checkpoints

To isolate and resolve problems with NLSP, complete the following steps:

1

Determine connectivity.

Verify that all neighbors are displayed under the NLSP Neighbors
option in IPXCON. This will determine whether there is local
connectivity.

Verify that there are sufficient potential paths within each area.

Verify that all LANs are listed in the NLSP LANs table in IPXCON.

Verify that all NLSP routers are listed in the NLSP Routers table in
IPXCON.

2

Determine whether RIP is active.

Verify that the NLSP LANs window indicates that RIP packets are
being absorbed.

Verify that the Circuits table indicates the state of any system.

Common Problems

This topic discusses the following common problems and their potential
solutions:

Login Times Out (page 132)

Load Balancing over IPX Is Not Working (page 133)

Only One IPX Packet Is Sent and Received (page 133)

IPXCON Counters Are Increasing (Duplicate ID or Network Number)
(page 133)

Error Messages Are Displayed (Duplicate ID or Network Number) (page
134)

NLSP Decision Process Is Running Frequently (Duplicate System ID)
(page 135)

«
...
129
130
131
132
133
...
»

Содержание NETWARE 6

























































































































































Отзывы:

Нет отзывов