background image

FCC Caution

Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user's  authority to operate the equipment. 

This device complies with part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, and (2) 
this device must accept any interference received, including interference that may 
cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class 
B digital device, pursuant to  part 15 of the FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference in  a residential 
installation. This equipment generates, uses and can radiate radio frequency energy 
and, if not installed  and used in accordance with the instructions, may cause 
harmful interference to radio communications. However,  there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause 
harmful  interference to radio or television reception, which can be determined 
by turning the equipment off and on, the user is  encouraged to try to correct the 
interference by one or more of the following measures:  

—Reorient or relocate the receiving antenna.  

—Increase the separation between the equipment and receiver.  

—Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.  

—Consult the dealer or an experienced radio/TV technician for help.  

This equipment complies with FCC radiation exposure limits set forth for an 
uncontrolled environment .This equipment should be installed and operated with 
minimum distance 20cm between the radiator& your body.  

This transmitter must not be co-located or operating in conjunction with any other 
antenna or transmitter.

XI'AN 

NOVASTAR 

TECH 

CO.,LTD.

Содержание MCTRL 4K



















Отзывы: