manualshive.com logo in svg

NovaScale Blade 2021 Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
NovaScale Blade 2021 Series Скачать руководство пользователя страница 44

 26

NovaScale Blade 2021 Installation and User’s Guide 

 

•

For a list of processors that are supported by your NovaScale Blade Server, ask your Support 
Representative.

•

Thoroughly review the documentation that comes with the processor, so that you can determine 
whether you have to update the NovaScale Blade Server BIOS code. The latest level of BIOS 
code for your NovaScale Blade Server is available from your Support Representative.

•

The processor sockets in this server contain built-in termination for the processor bus; therefore, 
no terminator card is required if a processor socket 2 is empty. However, for proper airflow, this 
socket must contain a processor heat-sink filler, sometimes called a processor baffle.

•

The processor speeds are automatically set for this server; therefore, you do not have to set any 
processor frequency-selection jumpers or switches.

The following illustration shows how to install the second processor on the system board for the 
NovaScale Blade Server.

Complete the following steps to install an additional processor:

1. Read the safety information beginning on page iii and “Installation guidelines” on page 19.
2. Shut down the operating system, turn off the NovaScale Blade Server, and remove the 

NovaScale Blade Server from the NovaScale Blade Chassis unit (see “Installing and removing 
the NovaScale Blade Server from the NovaScale Blade Chassis unit” on page 20 for 
instructions).

3. Carefully lay the NovaScale Blade Server on a flat, non-conductive surface.

4. Open the NovaScale Blade Server cover (see “Opening the NovaScale Blade Server cover” on 

page 20 for instructions).

5. Remove the bezel assembly (see “Removing the NovaScale Blade Server bezel assembly” on 

page 21 for instructions).

6. Locate the processor socket on the system board.

7. Remove the heat-sink filler.

8. Install the processor: 

a.

Remove the protective cover, tape, or label from the surface of the processor socket, if one is 
present.

Heat sink

Microprocessor

Microprocessor
locking lever

Heat sink filler

Alignment marks

Содержание Blade 2021 Series



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды