manualshive.com logo in svg

NovaScale Blade 2021 Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
NovaScale Blade 2021 Series Скачать руководство пользователя страница 39

 Installing options 

 21

Complete the following steps to open the NovaScale Blade Server cover:

1. Read the safety information beginning on page iii and “Installation guidelines” on page 19.
2. Carefully lay the NovaScale Blade Server down on a flat, non-conductive surface, with the cover 

side up.

3. Press the blade-cover release on each side of the NovaScale Blade Server and lift the cover open, 

as shown in the illustration.

4. Lay the cover flat, or lift it from the NovaScale Blade Server and store for future use. 

Statement 21:

xx

 CAUTION:

Hazardous energy is present when the NovaScale Blade Server is connected to the power 
source. Always replace the blade cover before installing the NovaScale Blade Server.

Removing the NovaScale Blade Server bezel assembly

To install certain options, you must first remove the NovaScale Blade Server bezel assembly. The 
following illustration shows how to remove the bezel assembly from the NovaScale Blade Server.

Complete the following steps to remove the NovaScale Blade Server bezel assembly:

1. Read the safety information beginning on page iii and “Installation guidelines” on page 19.
2. Open the NovaScale Blade Server cover (see “Opening the NovaScale Blade Server cover” on 

page 20 for instructions).

3. Press the bezel-assembly release and pull the bezel assembly away from the NovaScale Blade 

Server approximately 1.2 cm (0.5 inch).

4. Disconnect the control-panel cable from the control-panel connector.

5. Pull the bezel assembly away from the NovaScale Blade Server.

6. Store the bezel assembly in a safe place.

Control panel
connector

Bezel-assembly
release

Bezel-assembly
release

Control-panel
cable

Содержание Blade 2021 Series



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды