manualshive.com logo in svg

Novametrix Medical Systems OXYPLETH 520A, Руководство по обслуживанию

Поделиться
Скачать
Novametrix Medical Systems OXYPLETH 520A Скачать руководство пользователя страница 70

Section 14

Calibration Tests

60

Model 520A Service Manual

5693-90-01

PRELIMINARY

14.2.3

Flip the monitor over to expose the bottom cover and remove the four
cover screws. Holding both the top and bottom halves together, flip the
monitor over again and set it on its bottom cover.

14.2.4

Lift the top cover from the monitor and set it aside. Set the Red Alert Bar
lens aside with the cover for safe keeping.

Test Procedure

14.3

Unless otherwise specified all measurements are with respect to isolated ground.
Use the top of R4 (end closest to IC2) as ground reference.

14.3.1

Attach a line cord and place the mains switch to the “|” position. Verify
that the green 

 LED on the front panel illuminates. The monitor may

power up when the Mains switch is set to“|”, if this occurs turn the monitor
off with the front panel button.

14.3.2

Measure the voltage at J102 pin 2 and verify 13.2 VDC ± 0.4 volts.
This voltage is dependent on a fully charged battery installed. If an
installed battery is less than fully charged, the measured voltage will not
match the expected voltage.

14.3.3

Simultaneously press the leftmost softkey and the power button.
While 

Calculating Checksum

 is displayed, press and hold the third

softkey from the right until 

Novametrix Inc Production Test

appears.

14.3.4

Measure the voltage at TP1. Verify 5.000V ± 50mV. Adjust VR1 if
necessary.

14.3.5

Verify the following voltages:

Location 

Signal Name

Voltage

IC40 pin 4

-VA

-12.00V ± 500mV

IC40 pin 8

+VA

12.00V ± 500mV

IC20 pin 28

VBACK

4.75V ± 250mV

IC37 pin 14

+V5

5.00V ± 250mV

IC37 pin 7

-V5

-5.00V ± 250mV

IC37 pin 10

VREF

2.500V ± 5mV

IC36 pin 1

4VREF

4.045V ± 50mV

IC30 pin 14

-4VREF

-4.045V ± 100mV

Содержание OXYPLETH 520A






































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды