Novametrix Medical Systems OXYPLETH 520A Скачать руководство пользователя страница 64

Страница: 64 / 133

Section 12

Functional Test

Model 520A Service Manual

5693-90-01

PRELIMINARY

normal power up sequence. Note that the system date and time are not af-
fected by this action.

Softkey #1

= EPROM Checksum Test, Production Test Mode

Turn the monitor on while holding

Softkey

(the leftmost softkey) and

the monitor calculates and displays the checksum value of the EPROM
containing the system software. Press and hold

Softkey #3

while the

checksum is displayed and the monitor enters Production Test Mode.

Softkey #2

=Extended Display and Watchdog Test

Turn the monitor on while holding

Softkey

(second from left) and all

front panel indicators and display segments illuminate for several sec-
onds. The watchdog now resets the monitor which should then execute its
normal power up sequence. Note that the

indicator will illuminate only

if the monitor is being powered from the AC Mains.

Figure 12.

Softkey Identification

Softkey #1

Softkey #2

Содержание OXYPLETH 520A






































































































































Результаты поиска

Содержание OXYPLETH 520A

Отзывы:

Бренды по названию

Популярные бренды

Novametrix Medical Systems OXYPLETH 520A, Руководство по обслуживанию

Результаты поиска

Содержание OXYPLETH 520A

Отзывы:

Бренды по названию

Популярные бренды