NorthStar 958 Скачать руководство пользователя страница 47

Страница: 47 / 50

958 Installation Manual, Rev. A1

Page 43

APPENDIX A: 958 system
technical specifications

TABLE 15: 958 technical specifications

Physical features/environmental

Interfacing

Waterproof control head

Two bi-directional NMEA I/O ports, 1 AUX port

10.4” diagonal color LCD

Two bi-directional RS-232 ports

Unsurpassed sunlight viewability

Interfaces to optional Northstar 490 for fishfinding or
to an optional Northstar radar

640x480 pixel, hi-temp, backlit, transmissive color
LCD
Flush mount standard

Waypoint upload/download capability to a PC (with
appropriate software)

High-contrast anti-reflective screen
Waterproof chart cartridge door

One VGA out port (connects to Northstar 1201
monitor and others)

Large, easy-to-use backlit controls

One VIDEO in port

Easy interfacing I/O plugs

NMEA input sentences: WPL and others

0 degrees Celsius - 55 degrees Celsius max 95%
relative humidity, noncondensing
10 - 36 volts DC power, 50 watts

200 PPNM speed output
Honk output
NMEA output sentences: APB, BOD, BWC, GGA,
GLC, GLL, GSA, GSV, LCD, HSC, MSS, RNN, RMC,
RMA, RMB, VTG, WCV, XTE, ZDA, ZTG. (Conforms
to NMEA v 2.0 and later. Supports 1.5 GLL and
BWC.)

Accepts most external loran receivers
Waypoint and route transfer between two 958’s (or a
957 and a Northstar 941/951/952)

Содержание 958



















































Результаты поиска

Содержание 958

Отзывы:

Похожие инструкции для 958

Бренды по названию

Популярные бренды

NorthStar 958, Руководство по установке

Результаты поиска

Содержание 958

Отзывы:

Похожие инструкции для 958

Бренды по названию

Популярные бренды