NorthStar 958 Скачать руководство пользователя

Страница: 12 / 50

SECTION TWO: Installing and wiring the 958

Page 8

958 Installation Manual, Rev. A1

Electrical power requirements

Power source

The 958 is a negative-ground system that’s reverse-polarity protected. Power requirement is 10 VDC
minimum to 36 VDC maximum with at least 16-gauge connecting wire.

Connecting the 958 to ship’s power

The 958 ships with a 10-foot power cable that you can lengthen to a

maximum

of 25 feet:

•

for a cable length up to 15 feet, the power connections must use 16-gauge

connecting wire or heavier

•

for a cable length from 15 to 25 feet, use 14-gauge connecting wire or heavier

TABLE 2: In t e r f a c e c o n n e c t o r f u n c t i o n s

Connector name

Connector function(s)

Connects to...

NMEA (NMEA I/O)
(18-pin port)

NMEA 1 input/output -------------->

NMEA 2 input/output -------------->

Honk alarm/200 ppnm ------------>

NMEA devices: radar, autopilot, etc.

Same as NMEA 1

Remote honk alarm (or speed indicator)

GPS (Antenna)
(7-pin RS232 port)

GPS/WAAS input/output --------->

Beacon input/output -------------->

2201 or 2301 GPS antenna
- or -
Northstar 2701 beacon receiver (optional)

AUX (Auxiliary)
(6-pin auxiliary NMEA
port)

RS-422/NMEA input/output ----->

Northstar 490 echo sounder (optional)

- or -

A second 958 (or to a Northstar 957/952/
951/941) to transfer waypoints and routes

PWR (Power)

Power

10 to 36 VDC, 50 watts

VGA (15-pin port)

Video output

Remote display

VIDEO (coaxial)

Video input

Any NTSC-compatible device

CAUTION!

As a good safety practice, Northstar strongly recommends
that you connect the 958 to a circuit breaker or 20-amp fuse
at the power source (battery).

Содержание 958



















































Результаты поиска

Содержание 958

Отзывы:

Похожие инструкции для 958

Бренды по названию

Популярные бренды

NorthStar 958, Руководство по установке

Результаты поиска

Содержание 958

Отзывы:

Похожие инструкции для 958

Бренды по названию

Популярные бренды