background image

20 

 

Start-Up Procedures 

Start the Engine to Power the Pump.   

 

1.

 

Make sure water supply is connected and primed.  

CAUTION: Warranty Void 

Running the pump dry will cause damage and void 

the warranty. 

 

2.

 

To prevent accidental spraying, engage the safety 
latch on spray gun trigger by rotating it to the 
locked position. 

3.

 

Follow the instructions in the Engine Manual for 
starting the engine. 

- If the engine doesn't start on the first try, 
pressure may build up in the pump.  Relieve 

pressure by squeezing the spray gun trigger 
before attempting to start engine again.  This 
will make starting easier. 

       

DANGER: Engine Exhaust 

Do not inhale engine exhaust.  It contains 
dangerous carbon monoxide that can kill you. 

 

Apply Cleaning Chemical (If Desired)  

1.

 

Make sure the chemical injector is properly set up 
according to the instructions. Reference “Set Up for 
Chemical Spray” on the previous page.  

2.

 

Make sure the low pressure BLACK nozzle is 

attached before beginning to spray chemicals -- 

Only the low pressure black nozzle will allow 
chemicals to be drawn through the chemical injector 
into the water stream. 

3.

 

Apply chemicals by squeezing the spray gun trigger.  
The chemical injector will draw the chemical into the 
water stream. 

4.

 

Apply chemicals evenly to the cleaning surface. 

Never use more chemical than is necessary to clean 
the surface. 

5.

 

Allow the chemicals time to react with the dirt before 
rinsing. 

6.

 

Prepare to rinse by changing to a high-pressure 
nozzle. Changing the nozzle from the low-pressure 
black nozzle to a high-pressure nozzle will stop the 
flow of chemicals into the water stream. 

 

Instructions for selecting a nozzle can be 
referenced in the “Connect Hoses, Water Supply, 
and Spray Nozzle” section, see the subsection 
“Select Nozzle for Spray Gun”.   

7.

 

Rinse with high-pressure spray as instructed below. 
 

Begin High Pressure Spray  

      WARNING: High Pressure Spraying                           

Safety  

 

Keep spray away from people.

 Never direct 

discharge stream at or near any person.  Do not 
allow any part of the body to come in contact with 
the fluid stream.  High-pressure spray can cause 

serious skin, eye, or falling injuries.  Injection injury 
will occur if high-pressure spray pierces the skin, 

injecting liquid under the skin.  Injection injury can 
result in blood poisoning and/or severe tissue 
damage leading to infection, gangrene and possibly 

amputation.  Seek medical attention. 

 

Do not secure trigger open.  

To reduce risk of 

injury, do not attempt to secure the spray gun open 
by blocking or tying the spray gun in the open 
position. 

 

Prevent slips / loss of balance

. High-pressure 

spray could cause you to lose balance from 
kickback forces, and wet surfaces can be slippery

.  

-

 

Keep good footing and balance at all times.  Do 

not overreach. 

-

 

Do not stand on unstable support when spraying.  

-

 

If spraying from an elevated surface, use fall 

protection because spray gun kickback can 
propel you off the elevated surface. When 

spraying from a ladder or scaffolding, ensure it is 
firmly anchored from sway or tip-over. 

-

 

Be aware of puddles and slippery surfaces.  
Ensure there is adequate drainage to prevent 

pooling of water. 

 

Prevent surface damage & flying debris

 – 

Surfaces being sprayed must be strong enough to 
withstand high-pressure spray or damage may 
result. In addition, high-pressure spray will 

dislodge unsecured objects as well as surface 
chips and debris, resulting in hazardous flying 

objects that can cause personal injury or property 
damage.  Do not spray brittle surfaces or 
breakable, fragile, or unsecured objects such as: 

o

 

stucco or laminar flagstone 

o

 

some painted surfaces 

o

 

windows or glass doors (because they may 
break) 

o

 

light fixtures, flowerbeds, mailboxes 

o

 

unsecured, lightweight objects

 

 

Procedure: 
 

1.

 

Put on one of the high-pressure spray nozzles 
(always relieve system pressure first and follow 
instructions for attaching a nozzle). 

2.

 

Clear the cleaning area of all persons.  Keep 

children and pets away. 

3.

 

Hold the spray gun firmly with two hands and a 
sturdy stance -- Gun kicks back when triggered. 

Содержание 15775440







































Отзывы: