NorthStar 15775440 Скачать руководство пользователя страница 13

13 

 

inside RVs or other vehicles, on boats, or on 
pick-up truck beds. 

 

7.

 

WARNING: Location hazards 

Choose a suitable site for operating your pressure 
washer to prevent possible death from carbon monoxide 
poisoning or injury from fire/explosion, hot surfaces or 
equipment tip-over.  

Positioning

1.

 

The pressure washer should be positioned on a 
firm, level (less than 3 degree slope), heat-
resistant surface with good drainage and a 

nearby water supply.   

2.

 

The pressure washer should be placed within 
garden hose distance of a continuous water 
supply.  Ensure that the pressure washer sits 

level and will not slide or shift during operation.  
If applicable, block the pressure washer's 
wheels to prevent movement.   

3.

 

Situate so there is adequate pulling room for 

starting the engine using the recoil starter. 
Attempting to pull at an odd angle could rip off 
grip cord and/or cause muscular injuries to the 
operator. 

Airflow

1.

 

Situate so there is adequate clearance around 
pressure washer to allow for airflow – at least 7 
feet from any non-combustible wall or 

obstruction.   

2.

 

Do not operate with a tarp, blanket, or cover 
surrounding the machine. 

3.

 

Do not place any objects against or on top of 

the unit. 

4.

 

The pressure washer needs adequate, 
unobstructed flow of air to allow for proper 
combustion and adequate cooling.

  

Proper 

combustion can only be obtained when there is 
a sufficient supply of oxygen available for the 
amount of fuel being burned.  Cooling 
ventilation is required to prevent overheating of 

the pressure washer and possible fire. 

 
Exhaust

WARNING: Exhaust Modification hazard 

Never attempt to attach ductwork to the muffler system 

to allow for installation inside an enclosure. This could 
cause heat build-up and increased exhaust back-
pressure, resulting in possible exhaust leakage or 
damage to the pressure washer. 

1.

 

The exhaust gas from your pressure washer is 
extremely hot and can cause combustible 

materials to catch on fire.   

2.

 

Make sure the engine is at least 7 feet from all 
combustible materials and structures during 
operation. 

3.

 

Keep a fire extinguisher rated "ABC" nearby.  
Keep it properly charged and be familiar with its 
use. 

4.

 

Place the unit so that the exhaust fumes will not 

be directed towards people or building air 
intakes.  

 

 

 DANGER: Carbon monoxide hazard 

Exhaust fumes from the engine contain carbon 

monoxide (CO), a poisonous gas you cannot see, 
smell, or taste. The CO generated by the engine can 

rapidly accumulate, even in areas that appear to be well 
ventilated, resulting in dangerous and fatal 
concentrations within minutes. NEVER run pressure 

washer inside any enclosed or semi-enclosed spaces, 
including homes, garages, basements, sheds, boxes, 
pick-up truck beds, RVs, or boats. These spaces can 

trap poisonous gases, EVEN if you run a fan or open 
windows. If you start to feel sick, dizzy, or weak while 

using the pressure washer, shut off the engine and get 
to fresh air RIGHT AWAY. See a doctor. You may have 
carbon monoxide poisoning.

 

 

Install Spark Arrestor (if Required) 

Equip engine with spark arrestor if machine will be 
used near any ignitable forest, brush, or grassy 

land. (See engine Owner’s Manual provided to 
determine if the engine is already equipped.) Make 
sure you comply with applicable local, state, and 
federal codes. 

 

 

Содержание 15775440







































Отзывы: