NORTHROP GRUMMAN Iklwa II Скачать руководство пользователя страница 1

Страница: 1 / 6

SERVICE BULLETIN

Note No.

SVC-FSB-0050

Release Date

11/20/2017

Contact

[email protected]

SVC-FSB-0050 Iklwa II and Patara II

Shutter Assembly Repair Procedure

Iklwa II and Patara II Shutter Assembly Repair
Procedure

Purpose

This service bulletin describes the process for repairing a shutter assembly that binds
while attempting to open and close due to incorrect hardware or incorrect arm alignment.

Scope

This service bulletin applies to shutter assemblies in Iklwa II and Patara II lasers
manufactured prior to July 11, 2017.

Responsibilities

The NG CEO Technical Service Department is responsible for the content of this service
bulletin.

Safety Requirements

CAUTION.

Ensure the laser is turned off and unplugged from the electrical source prior

to performing this operation.

Tools and Equipment



3/32" Hex Driver



5/64" Hex Driver



9/64" Hex Driver



3/16" Nut Driver



Diagonal Cutter



Gloves



Small Cable Tie

Procedure

Remove Laser Cover

1.1.

Move the laser to a clean area.

Содержание Iklwa II







Результаты поиска

Содержание Iklwa II

Отзывы:

Похожие инструкции для Iklwa II

Бренды по названию

Популярные бренды

NORTHROP GRUMMAN Iklwa II, Процедура ремонта

Результаты поиска

Содержание Iklwa II

Отзывы:

Похожие инструкции для Iklwa II

Бренды по названию

Популярные бренды