Northern Lights OM844W3 Скачать руководство пользователя

Страница: 29 / 36

OM844W3 5/11

Troubleshooting

ENGINE

PROBLEM

POSSIBLE CAUSE

RECOMMENDATION(S)

High Fuel Consumption

Fuel leakage

• Improper installation or tightening.

(continued)

Excessive load on engine

• Check loads.

Below Normal

Thermostat not working properly

• Check thermostat.

Engine Temperature

Temperature gauge

• Check water temperature with thermometer.



not working properly

Engine Malfunctions at
High Output Range

Fuel supply insuffi cient

• Air in fuel system or clogged fuel fi lter

element

Fuel injection amount between

plungers uneven

• Check fuel injectors

Valve clearance adjusted incorrectly • Re-adjust valve clearances

Valve spring broken

• Replace valve spring

Governor spring broken

• Replace governor spring

Low Oil Pressure

Low oil level

• Fill crankcase to proper level.

Improper type of oil

• Drain and fi ll crankcase with correct oil.

Partially plugged oil fi lter

• Replace fi lter. Check bearings, oil pump,

and relief valve for wear.

High Oil Consumption

Break-in period

• Oil consumption decreases after break in.

Crankcase oil too light

• Use proper viscosity oil.

Oil leaks

• Check for leaks in lines around gaskets

and drain plug.

Engine Emits Black

Clogged or dirty air cleaner

• Service air cleaner.

or Gray Exhaust Smoke

Defective

muffl er

• Have dealer check back pressure.

(back pressure too high)

Improper fuel

• Use correct fuel for temperature.

Injection nozzles dirty

• See your dealer.

Engine timing off

• See your dealer.

Engine Emits

Improper fuel

• Use correct fuel for temperature.

White Smoke

Cold engine

• Warm up engine to normal operating

temperature.

Defective thermostat

• Remove and check thermostat.

Engine timing off

• See your dealer.

If you cannot correct problems with these procedures, see your

Northern Lights

dealer.

Содержание OM844W3





































Результаты поиска

Содержание OM844W3

Отзывы:

Похожие инструкции для OM844W3

Бренды по названию

Популярные бренды

Northern Lights OM844W3, Руководство оператора

Результаты поиска

Содержание OM844W3

Отзывы:

Похожие инструкции для OM844W3

Бренды по названию

Популярные бренды