Northern Lights OM844W3 Скачать руководство пользователя страница 18

Страница: 18 / 36

OM844W3 5/11

Servicing

LUBRICATION - GENERAL

1. Use only clean, high quality lubricants stored in

clean containers in a protected area.

2. These lubricants are acceptable:

a. API Service CC/CD/CE single viscosity oils.

b. API Service CC/CD/SF multi-viscosity oils.

3. Use the proper weight oil for your average
operation

temperature.

Figure 4: Lube Oils

4. Some increase in oil consumption may be

expected when SAE 5W and SAE 5-20W oils are
used. Check oil level frequently.

5. Never put additives or fl ushing oil in crankcase.

SP1. CHECKING OIL LEVEL

1. Check the oil level in the crankcase with the dipstick

(Fig. 5)

. The oil level must be in the waffl ed area

on the stick. Never allow the level to go below this
area. Follow the lubrication recommendations above.

SP2. OIL CHANGES

1. The set is delivered with special break-in oil.

Change the engine oil and oil fi lter after 50 hours

of operation. Use Service CC 30 weight oil during
the fi rst 100 hours.

2. Change the oil and fi lter again at 100 hours using the

oil recommended in the above diagram. After this,
change oil and fi lter every 250 hours.

3. During intermittent cold weather operation, change

oil every 100 hours or six weeks, whichever comes
fi rst.

4. Change oil at the end of each season and the

beginning of each season.

5.  Change oil when engine is warm.
6.  Dispose of waste oil in an approved manner.
7.  Never use a fl ushing oil.
8.  Loosen the clamp on the oil change tube. Remove

cap. Drain oil. Replace the cap and tube.

9. Refi ll engine with recommended oil for the season.
10. Engine capacity with new oil fi lter is:

844W3 and 844LW3 – 2.1 gallons

(8.2

liters)

SP3. CHANGING LUBE OIL FILTER

1. Change the lube oil fi lter every 250 hours.
2. Use

fi lter wrench to remove old fi lter. Dispose of

fi lter in approved manner.

3. Make sure the gasket from the old fi lter is removed

and discarded. Clean mount face.

4. Spread a thin fi lm of engine oil on the rubber gasket

on the new fi lter and screw it on nipple until gasket
meets the sealing surface.

5. Using hands only – no wrench – tighten fi lter

one-half turn farther. Overtightening can do

damage

fi lter housing.

6. Fill engine with recommended oil. Start engine and

check for leakage. Stop engine, wait 3 minutes, and
check oil level. Add additional oil if necessary.

7. Oil

fi lter part number is:

844W3 and 844LW3 – #24-03100

Air

Single

Multi-

Temperature

Viscosity

Above

32°F

SAE 30W

SAE 15-40W

(0°C)

-10 to 32°F

SAE 10W

SAE 10-30W

(-23 to 0°C)

Below

-10°F

SAE 5W

SAE 5-20W

(-23°C)

Figure 5

Figure 6

Содержание OM844W3





































Результаты поиска

Содержание OM844W3

Отзывы:

Бренды по названию

Популярные бренды

Northern Lights OM844W3, Руководство оператора

Результаты поиска

Содержание OM844W3

Отзывы:

Бренды по названию

Популярные бренды