manualshive.com logo in svg

Northern Lights OM844W3, Руководство оператора

Поделиться
Скачать
Northern Lights OM844W3 Скачать руководство пользователя страница 19

OM844W3  5/11

17

SP4.  AIR CLEANER

1.  Inspect air cleaner every 250 hours. In dusty condi-

tions, check more often.

2.  Marine sets: if dirty, wash element in soapy water. 

Rinse and dry thoroughly before re-installing.

 

Replace if necessary. The element part number is:

 

 

M844

W3

 and M844

LW3

  –  #24-23100

3.  C-Series sets: the element cannot be cleaned. 

Replace it when necessary. Part number is:

 

 

M20

CRW3

  –  #24-28401

4. 

NOTE: Make absolutely sure no impurities enter 

the engine while changing the element. Do NOT 
run the engine with the air cleaner removed.

SP5.  V-BELTS

1.  Check the tension and wear on the V-belt daily.
 
2.  Use your thumb to press on the belt at the midpoint 

between the crankshaft and alternator pulleys. The 
tension is correct if the belt can be depressed about 
3/16 in. (5 mm) .

Servicing

Figure 8:  Valve Adjustment

SP6.  VALVE CLEARANCES

1.  Adjust valve clearance after 1000 hours or as 

needed.

2.  Valve adjustments should be done after the cylinder 

head bolts have been re-tightened. Engine should be 
cold and NOT running.

3.  Watch the valves while turning the engine over by 

hand. Turn until the inlet valve starts to open and 
the exhaust valve starts to close (the valves are 
rocking). Then turn the crankshaft one more full 
turn and adjust the clearance on both valves for this 
cylinder.

 

Align the top mark of the crank pulley with the top 

mark of the timing gear case.

4.  Loosen the lock nut and adjust the clearance 

between the rocker arm and valve guide of both the 
intake and exhaust valves with the adjustment screw 
(

Figure 8

). Clearance on both intake and exhaust 

valves should be 0.008 in. (0.2 mm).

5.  Repeat steps 3 and 4 for each cylinder. Each set of 

valves must be adjusted individually.

6.  Replace the rocker arm cover. Tighten cover nuts to 

5 - 8 ft/lbs (0.8 - 2.3 kg/m).

Figure 7:  844W3 and 844LW3 Valve sequence

In     Ex       In     Ex       In      Ex       In      Ex

No. 1          No. 2           No. 3           No. 4

Cylinder

Valve

Arrangement

When No. 1

cyl. is at TDC

in compression

stroke

With the 

crankshaft

turned by 360

0 

in normal

direction from

above

Содержание OM844W3





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды