Northern Lights OM844W3 Скачать руководство пользователя страница 26

Страница: 26 / 36

OM844W3 5/11

If you cannot correct problems with these procedures, see your

Northern Lights

dealer.

Troubleshooting

DC ELECTRICAL SYSTEM

PROBLEM

POSSIBLE CAUSE

RECOMMENDATION(S)

Battery Will Not Charge

Loose or corroded connections

• Clean and tighten battery connections.

Sulfated or worn out batteries

• Check specifi c gravity of each battery.

• Check electrolyte level of each battery.

Loose or defective alternator belt

• Adjust belt tension.

•

Replace

belt.

Starter Inoperative

Check DC circuit breaker

• If the breaker is tripped, reset it.

Loose or corroded connections

• Clean and tighten loose battery and

harness plug connection.

Low battery output

• Check specifi c gravity of each battery.

• Check electrolyte level of each battery.

Defective electrical system

• Repair or replace.

ground wire:

Starter Cranks Slowly

Low battery output

• Battery is too small.

• Battery cables are too small.

Check

specifi c gravity

• Replace battery if necessary.

of each battery

Check electrolyte level

• If low, fi ll cells with distilled water.

of each battery

Crankcase oil too heavy

• Fill with oil of appropriate viscosity.

Loose or corroded connections

• Clean and tighten loose connections.

Entire Electrical System

Check DC circuit breaker

• If breaker is tripped, reset it.

Does Not Function

Faulty connection

• Clean and tighten battery and harness

plug

connections.

Sulfated or worn out batteries

• Check specifi c gravity and electrolyte

level of each battery.

Содержание OM844W3





































Результаты поиска

Содержание OM844W3

Отзывы:

Похожие инструкции для OM844W3

Бренды по названию

Популярные бренды

Northern Lights OM844W3, Руководство оператора

Результаты поиска

Содержание OM844W3

Отзывы:

Похожие инструкции для OM844W3

Бренды по названию

Популярные бренды