Northern Lights Lugger ONL753W2 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 27

Northern Lights Lugger ONL753W2 Скачать руководство пользователя страница 7

ONL753W2 10/09

7

Control Panel

Figure 3: Series 1-B Generator Control Panel

1. SHUTDOWN BYPASS-PREHEAT SWITCH

There are two functions built into this switch:

preheating the engine and bypassing the engine safety
shutdown circuit, enabling a quicker start. Hold the
switch in the ON position for approximately 10 to 20
seconds before starting a cold engine. Holding the
switch ON for too long can burn out the glow plugs.

NOTE: Three position Engine Control switches must be
in the RUN position during preheating. Preheat switch
must be held in ON position during starting.

2. ENGINE CONTROL SWITCH

To start the engine, hold this switch in the START

position until the engine is running.

NOTE: Excessive cranking of marine sets equipped

with water lift muffl er systems can cause engine
damage. See page 8.

After the engine starts, release the switch and it will
return to RUN position. To stop the engine, hold the
switch in the STOP position.

NOTE: The rocker switch is used on Series 1 panels
only, and has a light that glows when the set is running.

3. HOUR

METER

Keeps track of engine running time.

«
...
5
6
7
8
9
...
»

Содержание Lugger ONL753W2




























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды