Northern Lights and NL1066H3 Скачать руководство пользователя страница 6

ONL2-2  7/13

4

Safety Rules

updated 2/23/12

Operating equipment requires the full attention of 
the operator.  Do not use radio or music headphones 
while operating machinery. 

Practice Safe Maintenance

Understand all service procedures 
before starting work.  Keep area clean and dry.  
Never lubricate, service, or adjust machine while it is 
in operation.  

Keep hands, feet and clothing away from power-
driven equipment.  When shutting down an engine, 
disengage all power and operator controls. Allow 
the engine to cool completely before beginning any 
service work.  

Securely support any machinery elements that must 
be raised for service work with support or lifting 
machinery specifi cally intended for that purpose.

Keep all parts in good conditions and properly 
installed.  Fix damage immediately.  Replace any 
worn or broken parts.  Remove any build up of 
grease, oil or debris.

Disconnect battery ground cable (-) before making 
any adjustments or service work.  

Stay Clear of Rotating Drivelines

Entanglement in rotating drivelines can cause serious 
injury or death.  Keep shields in place at all times.  
Make sure that rotating shields turn freely in pace 
with the drivelines.

Do not wear loose fi tting equipment around rotating 
drivelines.  Stop the engine and make sure that all 
moving parts have stopped 
before making any adjustments, 
connections, or performing 
any other type of service to 
the engine or other driven 
equipment.        

Prevent accidental discharge of starting fl uids by 
storing all cans in a cool, safe place, away from sparks 
or open fl ame.  Store with cap securely on container.  
Never incinerate or puncture a fuel container. 

Prevent fi res by keeping machine clean of accumulated 
trash, grease and debris.  Always clean any spilled fuel 
as swiftly as possible.  Do not store oily rags, which 
can ignite and burn spontaneously. 

Be prepared if a fi re starts.  Keep a fi rst aid kit and fi re 
extinguisher handy.  Keep emergency contact numbers 
for fi re department, doctors, ambulance and hospital 
near the telephone.

Service Machines Safely

Do not wear a necktie, scarf, 
necklace, rings or other 
jewelry, or any loose clothing 
when working near moving 
parts.  Tie long hair behind your head.  If any of these 
items get caught in moving machinery, severe injury or 
death could result. 

Check for any loose electrical connections or faulty 
wiring.
 
Look completely around engine to make sure that 
everything is clear before starting.

Wear Protective Clothing

To prevent catching anything in moving machinery, 
always wear close fi tting clothes and safety equipment 
appropriate to the job.  
Prolonged exposure to loud noise can cause hearing 
loss or impairment.  
Wear suitable authorized 
hearing protection, such 
as earmuffs or plugs to 
protect against loud noises.

Содержание and NL1066H3










































Отзывы: