Northern Lights and NL1066H3, Руководство оператора

Страница: 20 / 41

ONL2-2 7/13
18
LUBRICATION
Break-in oil
1. Use one of the following during the fi rst 100 hours
of operation:
a. John Deere Engine Break-In Oil
b. API Service CC, CD, or CE oil
c. ACEA Specifi cation E1 or E2
2. Do not use John Deere PLUS-50 oil or engine oils
meeting API CI-4, CH-4, CG-4, CF-4, or CF-2,
ACEA E5, E4, or E3 performance levels during
the fi rst 100 hours of operation of a new or rebuilt
engine. These oils will not allow the engine to
break-in properly.
Lubrication - General
1. Use only clean, high quality lubricants stored in
clean containers in a protected area.
2. These oils are acceptable after the fi rst 100 hours:
a. API Service Catagory CI-4 or CH-4 oils.
b. ACEA Oil Sequence E4 or E5.
d. ACEA Oil Sequence E3.
3. Use the proper weight oil for your average operation
temperature, multi-viscosity diesel engine oils are
preferred. Quality and sulfur content must comply
with local existing emission regulations.
4. Some increase in oil consumption may be expected
when SAE 5W and SAE 5-20W oils are used. Check
oil level frequently.
5. Never put additives or fl ushing oil in crankcase.
SP1. CHECK ENGINE OIL LEVEL
1. Check the oil level in the crankcase, with the oil
dipstick, daily.
2. The oil level must be between the “Waffl ed area”
and the “add”. Never allow the level to go below the
“add”.
3. Always add the same viscosity of oil as is already in
the crankcase.
SP2. OIL CHANGES
1. Using the oil recommended above, change the engine
oil and fi lter after the fi rst 50 hours of operation, the
fi rst 100 hours and every 250 hours thereafter.
2. During intermittent cold weather operation, change oil
every 100 hours or six weeks, whichever comes fi rst.
3. Change oil at any seasonal change in temperature
when a new viscosity of oil is required.
a. Remove plug from outlet in base frame. Screw in
owner-supplied drain hose.
b. Open valve at oil pan outlet. After oil has been
drained into suitable container, close valve, remove
drain hose and replace plug in base frame outlet.
c. Refi ll engine with recommended oil.
4. Engine Lube Oil Capacity:
SP3. CHANGING OIL FILTER
1. Change the lube oil fi lter every 250 hours.
2. Use
a fi lter wrench to remove old fi lter. Dispose of
fi lter in approved manner.
3. Make sure the gasket from the old fi lter is removed
and discarded.
4. Lubricate the rubber gasket on the new fi lter and screw
it on nipple until gasket meet the sealing surface.
5. Using hands only, no wrench, tighten fi lter one-half turn
farther. Overtightening can do damage to fi lter housing.
6. Fill engine with recommended oil. Start engine and
check for leakage. Stop engine and check oil level.
Add additional oil if necessary.
SP4. AIR CLEANER
1. Inspect air cleaner every 100 hours. Replace air
cleaner element every 500 hours.
2. Clean the rubber tube at the cleaner. Loosen the hose
clamp and the attaching strip for the cleaner.
3. Make sure the rubber tube is in good condition and
that new fi lter is absolutely clean and installed
properly.
4. Start the engine and check for leaks.
NOTE: Make absolutely sure no impurities enter the
engine while changing the element. Do not run the
engine with the air cleaner removed.
Air Single Multi
Temperature Viscosity Viscosity
Above 32°F
(0°C)
SAE-30W SAE15-40W
-10°F to 32°F
(-23°C to 0°C)
SAE-10W SAE10-30W
Below
-10°F
(-23°C)
SAE-5W SAE5-20W
NL1064D,T1,T2, H1 14.7 liters 15.5 qts.
NL1066T 20.0 liters 21.1 qts.
NL1066H1,H2,H3 31.5 liters 33.3 qts.
Servicing