manualshive.com logo in svg

Nortel RLC, Руководство по установке и администрированию

Nortel RLC - устройство для коммутации VLAN с возможностью управления трафиком. Для установки и настройки обязательно скачайте "Руководство по установке и администрированию" бесплатно с {сайт} для подробной информации о продукте.

Поделиться
Скачать
background image

RLC Installation and Administration Guide

393

June 2005 

Glossary 

D  

daughterboard

Usually used as a synonym for an expansion board, a daughterboard is any 
printed circuit board that connects directly or indirectly to a motherboard.

DB9 connector

A 9-pin connector labeled ADMIN that provides the RS-232 serial port 
interface. This serial port connection can be used to configure a Remote 
Gateway 9150 unit that is directly connected to a PC.

DC 

Refer to

 Direct Current.

DHCP

Refer to

 Dynamic Host Configuration Protocol.

Digital Linear Tape

A high-capacity 1/2-inch streaming tape cartridge format.

Digital Signal Processor

A special type of coprocessor that manipulates analog data, such as sound or 
photographs, that has been converted to digital form.

DIMM

Refer to

 Dual In-line Memory Module.

DIP 

A type of protective packaging for silicon memory chips that provides a safe and 
convenient means of installing and removing the chip.

DIP switch

A series of tiny switches built into circuit boards that enables you to configure a 
circuit board for a particular type of computer or application. DIP switches are 
always toggle switches. This means that they have two possible positions: on or 
off (or 1 or 0).

Содержание RLC



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RLC

Accuphase AD-60 Instruction Manual preview
AD-60
Бренд: Accuphase Страницы: 2
ADTRAN ATLAS 550 Manual preview
ATLAS 550
Бренд: ADTRAN Страницы: 2
Acrosser Technology AMB-VDX3H1 Series Quick Start Manual preview
AMB-VDX3H1 Series
Бренд: Acrosser Technology Страницы: 4
ebm-papst VBH0630CTTRS Operating Instructions Manual preview
VBH0630CTTRS
Бренд: ebm-papst Страницы: 16
IBM TotalStorage SAN16M-R SAN Installation And Service Manual preview
TotalStorage SAN16M-R SAN
Бренд: IBM Страницы: 116
Opvimus UMX-ETH+ Operating Instructions Manual preview
UMX-ETH+
Бренд: Opvimus Страницы: 12
Oracle Talari E1000 Installation Manual preview
Talari E1000
Бренд: Oracle Страницы: 24
Cypress Semiconductor CY7C1034DV33 Specification Sheet preview
CY7C1034DV33
Бренд: Cypress Semiconductor Страницы: 9
Enginko MCF-LW06424 Operating Manual preview
MCF-LW06424
Бренд: Enginko Страницы: 19
ekwb EK-FC Installation Manual preview
EK-FC
Бренд: ekwb Страницы: 2
IFM Electronic OVP800 Operating Instructions Manual preview
OVP800
Бренд: IFM Electronic Страницы: 14
Cabletron Systems SmartSwitch 8-slot User'S Reference Manual preview
SmartSwitch 8-slot
Бренд: Cabletron Systems Страницы: 150
TP-Link TD-VG5612 Quick Installation Manual preview
TD-VG5612
Бренд: TP-Link Страницы: 2
Waveshare High-Precision AD/DA Board User Manual preview
High-Precision AD/DA Board
Бренд: Waveshare Страницы: 8
Airlink101 AR725W User Manual preview
AR725W
Бренд: Airlink101 Страницы: 64
ETAS ES1337.2 User Manual preview
ES1337.2
Бренд: ETAS Страницы: 29
ADS Technologies PTV-370 Driver Manual preview
PTV-370
Бренд: ADS Technologies Страницы: 1
CSL 300295 User Manual preview
300295
Бренд: CSL Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды