Nortel 2500 Seriess Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 392

background image

Hardware components of the Ethernet Routing Switch 2500 Series

27

The 10BASE-T/100BASE-TX switch ports also support half- and full-duplex
mode operation.

The 10BASE-T/100BASE-TX RJ-45 switch ports can connect to 10 Mb/s or
100 Mb/s Ethernet segments or nodes.

ATTENTION

Use only Category 5 copper Unshielded Twisted Pair (UTP) cable connections
when connecting 10BASE-T/100BASE-TX ports.

Auto-MDI/MDI-X

The 10/100BASE-TX port connectors support auto-MDI/MDI-X.

Typical MDI-X ports connect over straight-through cables to the Network
Interface Card (NIC) in a node or server, similar to a conventional Ethernet
repeater hub. However, with the auto-MDI/MDI-X feature, you can still use
straight-through cables while connecting to an Ethernet hub or switch.

The auto-MDI/MDI-X feature is dependent on the autonegotiation feature.
If autonegotiation is enabled on a port, the auto-MDI/MDI-X feature is
automatically enabled on the port as well. If autonegotiation is disabled on a
port, then the port operates as a standard MDI-X port.

Power over Ethernet on Ethernet Routing Switch 2526T-PWR
and 2550T-PWR

The Ethernet Routing Switch 2526T-PWR and 2550T-PWR provide IEEE
802.3af-compliant power over the PoE-labeled front-panel RJ-45 ports. The
switches provide power discovery and power management on each port
basis. You can use the PoE ports to provide power to network appliances,
such as IP Phones, wireless access points, and video devices.

You can enable or disable power to individual ports. For information about
configuring PoE, see

"Power over Ethernet for the Ethernet Routing Switch

2526T-PWR and 2550T-PWR" (page 157)

.

LED display panel

Figure 6 "LED display panel" (page 28)

shows the LED display panel of the

Ethernet Routing Switch 2500 Series. See

Table 2 "Ethernet Routing Switch

2500 Series LED descriptions" (page 28)

for a description of the LEDs.

Nortel Ethernet Routing Switch 2500 Series

Overview — System Configuration

NN47215-500 (323162-B)

02.02

Standard

4.1

19 November 2007

Copyright © 2007, Nortel Networks

.

«
...
25
26
27
28
29
...
»

Содержание 2500 Seriess









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2500 Seriess

Бренд: D-Linke Страницы: 32

MatrixPRO-II DVI 16x16

Бренд: Barco Страницы: 43

Бренд: Barco Страницы: 5

Бренд: Qualys Страницы: 2

Бренд: T&D Страницы: 122

Бренд: Patton electronics Страницы: 12

Бренд: Ravpower Страницы: 27

Бренд: Idis Страницы: 20

UniFi LED ULED-AT

Бренд: Ubiquiti Страницы: 16

Бренд: Comtrend Corporation Страницы: 4

Бренд: Linksys Страницы: 6

Бренд: MaxComm Страницы: 10

Бренд: Quatech Страницы: 98

Бренд: E-Lins Страницы: 10

LN1000 - RELEASE NOTES 8-27-2010

Бренд: Juniper Страницы: 64

ReadyNAS Duo v2

Бренд: NETGEAR Страницы: 100

Бренд: Patton electronics Страницы: 8

Бренд: H3C Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды