Nortel 1750 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 108

Nortel 1750 Скачать руководство пользователя страница 85

Appendix A Technical specifications

85

Nortel VPN Router Installation — VPN Router 1750

1000BASE-T (1000 MT) Ethernet interface card

Use the 1000BASE-T (1000 MT) Ethernet interface card to connect to Gigabit
Ethernet interfaces on other devices in your network, as well as to provide
increased throughput. This interface card has a single RJ-45 connector.

Figure 34

shows the 1000BASE-T (1000 MT) Ethernet interface card.

Figure 34

1000BASE-T (1000 MT) Ethernet interface card

The port on the 1000BASE-T Ethernet interface card accommodates an RJ-45
straight-through cable. Select cables for this port as follows:

•

For 1000BASE-T operation, use Category 5 four-pair Ethernet wiring. The
cable must comply with the TIA 568 wiring specification. Nortel recommends
a maximum length of 100 meters for the cable segment.

•

For 100BASE-TX operation, use Category 5 twisted-pair wiring: one pair
each for transmit and receive operations. The cable must comply with the

EIA 568 wiring specification. Nortel recommends a maximum length of 100
meters for the cable segment.

•

For 10BASE-T operation, use Category 3, 4, or 5 twisted-pair wiring.

Table 22

provides the 1000BASE-T (1000 MT) Ethernet port pinouts.

Table 22

1000BASE-T (1000 MT) Ethernet port pinouts

Pin

Description

1

TP0+

2

TP0-

3

TP1+

4

TP2+

5

TP2-

6

TP1-

11287EA

10 = OFF

100 = GR

N

1000 = ORG

A

CT/L

N

K

Intel PR

O

R

CS260010A

12345678

«
...
83
84
85
86
87
...
»

Содержание 1750













































































































Отзывы:

Нет отзывов