manualshive.com logo in svg

Nortel 1750, Инструкция по установке, Страница: 37 / 108

Поделиться
Скачать
Nortel 1750 Скачать руководство пользователя страница 37

Chapter 1  Cabling the VPN Router and turning the power on  

37

Nortel VPN Router Installation — VPN Router 1750 

T1/E1 CSU/DSU WAN interface card LEDs

Figure 10

 shows the LEDs on the T1/E1 CSU/DSU WAN interface card.

Figure 10   

LEDs on the T1/E1 CSU/DSU WAN interface card

Table 11

 describes the LEDs on the T1/E1 CSU/DSU WAN interface card.

Table 11   

LED indicators on the T1/E1 CSU/DSU WAN interface card

LED

Indicator

Description

LED 1

Red

The red alarm LED is lit when a loss-of-signal (LOS) or 

out-of-frame (OOF) condition is detected on the receive 

signal.

LED 2

Blue

The blue alarm LED is lit when receiving an upstream 

failure denoted by an alarm indication signal (AIS).

LED 3

Yellow

The yellow alarm LED is lit when the far-end equipment 

is in the red alarm condition.

LED 4

Green

The green LED is lit when the condition is normal 

operation.

CS160012A

LED 4, Green

LED 3, Yellow

LED 1, Red

LED 2, Blue

Содержание 1750













































































































Отзывы:

Нет отзывов