Nortel 1000BASE-XD Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 100

background image

Installing a Passport 8100 Module

204515-C

2-5

5.

Tighten the retaining screws to secure the module in the chassis
(

Figure 2-5

).

Figure 2-5.

Securing the Module in the Chassis

Turning On the Chassis Power

Although you can install or replace modules in an operating chassis, in a new
installation you may prefer to install all the modules before turning on the chassis
power.

To turn on the chassis power:

1.

Verify that all power cords are connected properly, as described in the
installation instructions for the power supplies.

2.

Turn all the power switches to the On position.

Note:

In a chassis with two power supplies in a nonredundant power

configuration, you must turn on both power supply units within 2 seconds of
each other. If you wait longer to turn on the second power supply, both power
supplies will shut down. To correct this condition, turn off both power
supplies, wait at least 30 seconds, and then turn on both power supplies again
within 2 seconds.

9400FA

«
...
39
40
41
42
43
...
»

Содержание 1000BASE-XD





































































































Отзывы:

Нет отзывов

Похожие инструкции для 1000BASE-XD

Бренд: Tailfin Страницы: 4

Бренд: T-Tech Страницы: 38

Бренд: 7AMEnfant Страницы: 2

Бренд: Bang & Olufsen Страницы: 12

Бренд: Gates Underwater Products Страницы: 49

Бренд: Gates Underwater Products Страницы: 45

STEVAL-IOD04KT1

Бренд: ST Страницы: 13

Бренд: Compass Страницы: 16

Бренд: Gator Страницы: 8

Бренд: Zooka Sports Страницы: 32

Бренд: Camtree Страницы: 3

AVID DISC BRAKES

Бренд: Avid Technology Страницы: 2

GemLightbox Aerial

Бренд: Picup Media Страницы: 13

Бренд: Heatilator Страницы: 3

Бренд: minnid Страницы: 44

Бренд: PCB Piezotronics Страницы: 12

Бренд: OnStar Страницы: 22

Бренд: Lamp Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды