manualshive.com logo in svg

Nortel 1000BASE-XD, Инструкция по использованию

Поделиться
Скачать
Nortel 1000BASE-XD Скачать руководство пользователя страница 28

Using the Passport 8100 Modules

1-8

204515-C

Passport 8132TX 32-Port I/O Module

The Passport 8132TX module (

Figure 1-3

) is a single-slot I/O module for the 

Passport 8000 Series chassis. It has 32 autosensing 10BASE-T/100BASE-TX 
switched ports with RJ-45 connectors. The ports have integrated LEDs to indicate 
port operation, and the module has three additional LEDs to indicate system 
operation. An expansion slot allows you to install an MDA to provide additional 
port types. You can add 10/100BASE-T, 100BASE-FX, or Gigabit Ethernet ports 
by installing an optional MDA in the Passport 8132TX module. Inserter/extractor 
levers and captive retaining screws are at each end of the module.

Figure 1-3.

Passport 8132TX Edge Switch Module

10BASE-T/100BASE-TX Port Connectors

The Passport 8132TX module provides 32 10/100 Mb/s autosensing ports that 
support the IEEE 802.3u autonegotiation standard. Each port can operate in full- 
or half-duplex mode. When a port is connected to another device that also 
supports the IEEE 802.3u standard, the two devices negotiate the best speed and 
duplex mode of operation. 

The port connectors are 8-pin modular RJ-45 connectors configured as MDI-X 
(media-dependent interface-crossover) connections. You can connect these ports 
to an MDI port (for example, a workstation or server) using a straight-through 
cable. If you are connecting to a device that does not have an MDI port, use a 
crossover cable (see

“MDI and MDI-X Connections” on page A-12

).

Refer to 

Appendix A, “Technical Specifications

,” for more information about the 

RJ-45 port connectors.

Note: 

 For 10 Mb/s connections, you can use Category 3, 4, or 5 copper 

unshielded twisted pair (UTP) cable. Use only Category 5 UTP cable to 
connect ports that will operate at 100 Mb/s.

9155EA

Содержание 1000BASE-XD





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды