background image

2

  

MM271 Installation Instructions

MM271 Installation Instructions

  

3

1

3

5

11

1

6

2

Q

K

U

7

3

6

8

9

10

M

L

T

6

11

V

OPEN gate and reattach operator with clevis pin. Check to 
ensure the operator is level.

Secure post pivot bracket to post bracket with the hardware 
provided (Q,K,U) when you have achieved the 1” clearance 
shown in Step 5 in both open and closed positions.

Mark middle of post bracket slots on fence post. Mark middle 
of gate bracket slots on gate cross support.

Remove clamps, post bracket, gate bracket, and operator. Then 
use a hammer and center punch to mark  
hole positions.

Drill holes completely through gate post and gate cross support.

Attach post bracket assembly to gate post. 

NOTE:

 Must be 

through bolted.

GATE OPERATOR INSTALLATION

1

2

3

5

6

12

T

L

L

V

P

2

1

1

13

2

14

15

4

H

1

5

1

2

2

1

Attach and secure operator assembly to brackets.

Attach gate bracket assembly to gate cross support.

Check for level. Adjust post bracket if necessary.

Tighten all bolts and remove excess length on post and gate 
bracket bolts with hacksaw.

Remove the arm from the front bracket then attach closed position stop 
plate to the leading edge of the gate with one of the following:

  • 

U-bolts

—tube and chain link gates (Not included)

  • 

Wood/lag screws

—flat aluminum/wood supports (Not included). 

Position gate stop with gate CLOSED to fence post. Tighten 
fasteners. Cut off excess bolt length.

GATE OPERATOR INSTALLATION

CLOSED POSITION STOP PLATE INSTALLATION

Содержание Mighty Mule MM271




















Отзывы: