background image

3

IMPORTANT SAFETY INFORMATION

INSTALLER: Please read all instructions before servicing 

this equipment. Pay attention to all safety warnings and 

any other special notes highlighted in the manual. Safety 

markings are used frequently throughout this manual to 

designate a degree or level of seriousness and should not 

be ignored. 

WARNING

 indicates a potentially hazardous 

situation that if not avoided, could result in personal injury or 

death. 

CAUTION

 indicates a potentially hazardous situation 

that if not avoided, may result in minor or moderate injury 

or property damage.

 WARNING:

ELECTRICAL SHOCK, FIRE OR

EXPLOSION HAZARD

Failure to follow safety warnings exactly could 

result in serious injury or property damage.
Improper servicing could result in dangerous 

operation, serious injury, death or property 

damage.
Before servicing, disconnect all electrical 

power to furnace.
• Before servicing, disconnect all electrical 

power to the air handler.

•  When servicing controls, label all wires prior 

to disconnecting. Reconnect wires correctly.

•  Verify proper operation after servicing.

 WARNING:

NITROGEN

HEALTH

FLAMMABILITY

REACTIVITY

0 Minimal Hazard

1 Slight Hazard

1

0

0

B64EM & B64VM air handlers leave the factory 

with a nitrogen holding charge. Use caution 

when preparing coils for field connections. 

If repairs make it necessary for evacuation 

and charging, it should only be attempted 

by qualified, trained personnel thoroughly 

familiar with this equipment. Some local codes 

require licensed installation service personnel 

to service this type of equipment. Under no 

circumstances should the equipment owner 

attempt to install and/or service this equipment. 

Failure to comply with this warning could result 

in equipment damage, personal injury, or death.

REQUIREMENTS & CODES

 WARNING:

This unit must be installed in accordance 

with instructions outlined in this manual 

during the installation, service, and operation 

of this unit. Unqualified individuals should 

not attempt to interpret these instructions or 

install this equipment. Failure to follow safety 

recommendations could result in possible 

damage to the equipment, serious personal 

injury or death.

• The installer must comply with all local codes and 

regulations which govern the installation of this type of 

equipment. Local codes and regulations take precedence 

over any recommendations contained in these instructions. 

Consult local building codes for special installation 

requirements.

• This equipment contains nitrogen gas. Installation or 

servicing should only be performed by qualified trained 

personnel thoroughly familiar with this type equipment.

•  All electrical wiring must be completed in accordance with 

local, state and national codes and regulations and with 

the National Electric Code (ANSI/NFPA 70) or in Canada 

the Canadian Electric Code Part 1 CSA C.22.1.

•  Installation of equipment may require brazing operations. 

Installer must comply with safety codes and wear 

appropriate safety equipment (safety glasses, work gloves, 

fire extinguisher, etc.) when performing brazing operations.

•  Install this unit only in a location and position as specified 

on 

page 4

 

page 5

This unit is designed only for Indoor 

installations and should be located with consideration 

of minimizing the length of the supply and return ducts. 

See 

Table 6, (page 16)

Table 7, (page 17)

Table 8, 

  (page 18)

Table 9, (pages 19 and 20)

 and the rating 

plate for proper circulating airflow data.

• Follow all precautions in the literature, on tags, and on 

labels provided with the equipment. Read and thoroughly 

understand the instructions provided with the equipment 

prior to performing the installation and operational 

checkout of the equipment.

• Air handler installations in a residential garage must be 

installed as specified on 

page 4

.

•  This air handler may not be used for temporary heating 

or cooling of buildings or structures under construction. 

Operating the air handler during construction is not 

permitted and will void the manufacturer’s warranty.

Содержание B64EM Series





























Отзывы: