Noritz Eco TOUGH NRCP111-DV-LP Скачать руководство пользователя страница 17

Страница: 17 / 44

Vent Pipe Installation

Chapter 4. – Installation

Concentric PVC/CPVC Termination

• The concentric termination may be shortened, but not lengthened from its original factory supplied length.

• 2" (50mm) & 3" (75mm) PVC or CPVC pipe may be used with the concentric termination. Reducers will be needed to connect 2" pipe.

Maintain the same vent pipe diameter from the water heater flue to the termination.

• Do not exceed the maximum vent lengths as specified in this section.

• There must be a 1" (25mm) to 4" (100mm) clearance between the outside wall and the air intake section of the termination as

illustrated on the left.

• Install a securing strap to prevent movement of the termination.

• Terminate at least 12" (300mm) above grade or above snow line.

• Terminate at least 7' (2.1m) above a public walkway, 6' (1.8m) from the combustion air intake of any appliance, and 3' (0.9m) from any

other building opening, gas utility meter, service regulator etc.

• Terminate at least 3' (0.9m) above any forced air inlet within 10' (3m), 1' (0.3m) below, 1' (0.3m) horizontally from or 1' (0.3m) above

any door, window, or gravity air inlet into any building per National Fuel Gas Code ANSI Z223.1/NFPA 54.

• Slope the horizontal vent 1/4” upwards for every 12" (300mm).

• Use a condensation drain if necessary.

Vent Pipe Installation (DV-Direct Vent)

Vertical

Horizonta

zG

|

o

z

XIGOY\PG

[IGOXWWP

pGiGzQQQ

GlGG{

QQQGuGG

GGGGGGS

GGGGGG U

l

p

l

|zGXYGGOZWP

QGuGGG
GGSGG

w}jGj

}GhGz

OJ}rTw}jT}hzP

zG

|

o

z

XIGOY\PG

[IGOXWWP

pGiGzQQQ

GlGG{

QQQGuGG

GGGGGGS

GGGGGG U

l

p

l

|zGXYGGOZWP

QGuGGG
GGSGG

w}jGj

}GhGz

OJ}rTw}jT}hzP

Содержание Eco TOUGH NRCP111-DV-LP













































Результаты поиска

Содержание Eco TOUGH NRCP111-DV-LP

Отзывы:

Похожие инструкции для Eco TOUGH NRCP111-DV-LP

Бренды по названию

Популярные бренды

Noritz Eco TOUGH NRCP111-DV-LP, Руководство по установке

Результаты поиска

Содержание Eco TOUGH NRCP111-DV-LP

Отзывы:

Похожие инструкции для Eco TOUGH NRCP111-DV-LP

Бренды по названию

Популярные бренды