background image

www.nordsonefd.com   [email protected]

   800-556-3484    Sales and service of Nordson EFD dispensing systems are available worldwide.

781Mini Series Spray Valve

7

Installation

NOTE:

 Prior to installing the valve, read the associated 

reservoir and valve controller operating manuals to become 
familiar with the operation of all components of the dispensing 
system.

Mounting the Valve on the Dispensing 
Equipment

1.  Mount the valve using the M4 mounting hole opposite the 

QR clasp.

CAUTION

Do not over-tighten the QR clasp thumb screw. Doing so can 
break the screw.

2.  Orient the fluid body and install the QR clasp as follows:

a.  Partially thread the QR clasp thumbscrew into the air 

cylinder body.

b.  When the thumbscrew is engaged, rotate the fluid 

body to the required alignment based on the use of a 
90° fluid inlet fitting.

c.  Finger-tighten the thumbscrew to fully secure fluid 

body to the air cylinder body.

Installing a 90° Fluid Inlet Fitting

1.  Thread the fitting nut fully onto the 90° fluid inlet fitting 

(towards the luer fitting).

2.  Fully thread the 90° fluid inlet fitting assembly into the 

valve fluid body, then unthread the assembly until the luer 
fitting is at the desired orientation.

NOTE:

 Do not unthread the 90° fluid inlet fitting more than 

one (1) turn.

3.  Use an 8-mm wrench to tighten the fitting nut against the 

fluid body.

QR clasp

Mounting bracket 
(P/N 7360613, 
optional)

Valve fluid 

body

90° fluid inlet 
fitting nut

Luer fitting

Содержание 781Mini Series



















Отзывы: