manualshive.com logo in svg

Norcold NX61, Руководство по обслуживанию

Поделиться
Скачать
Norcold NX61 Скачать руководство пользователя страница 57

www.norcold.com/cda

57

NX6 / NX8 / NXA Models

Refrigerator Service Manual

ICE MAKER

Specifi cations

Cycle....................... One revolution (eject and water 

fi

 ll)

Water 

fi

 ll capacity .............................4.7 

fl

 . oz. (140 mL)

Ice yield ............................3.5 lbs/24 hrs. (Approximate)
Cycle duration....................................... 3.5 to 7 minutes
Voltage................................................................120Vac
Amp draw
  Cycle on/heater on ................................................1.6 A
  Cycle on/heater off ................................................0.3 A
  Cycle off .................................................. No amp draw
Motor ........................................................1.5 W/8800 

Mold Heater .................................................185 W/72 

 

Fig. 45 - Ice Maker

The ice maker is a factory installed accessory. The 

components that support the ice maker are the water valve, 

water 

fi

 ll line, water 

fi

 ll tube, and the wire harness. The ice 

maker and components are shown in Fig. 45.

Wire Harness

The wire harness, Fig. 45(a) has four wires.

• 

Black–line (L) voltage with thermal fuse for ice mold 

overheating protection. It has an insulated female quick-

connect terminal.

• 

White–neutral (N). The insulated male quick-connect 

terminal is the 120 VAC neutral (N) conductor.

• 

Brown–supplies 120 VAC power to the water valve 

solenoid during the 

fi

 ll cycle. It connects to water valve 

solenoid M terminal.

• 

Green–ground. Connects to the metal cabinet metal 

plate along with the 120 VAC power cord ground wire.

Fill Tube

The 

fi

 ll tube is foamed into the top of the cabinet. It is not a 

replaceable component.

Water Valve

Fig. 45(b) shows an ice maker solenoid water valve that has a 

12VDC water line heater. The 12VDC heater is controlled by a 

thermostatic switch mounted on the valve's mounting bracket.
Fig. 45(c) shows an ice maker solenoid water valve without a 

12VDC water line heater.

Water Valve Assembly
without water line heater

Ice Bin

Cover

Fill Tube

Ice Maker

Wire Harness

Thermal Fuse

Black = L
White = N
Brown= V
Green = Ground

Connector

Water Valve Assembly
with water line heater

120 Vac Terminals

Heater
Wire Lead

s

Foil Type
Water Line
Heater

(a)

(b)

(c)

Shut-Off Arm

Содержание NX61































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды