11.4. Remove left and right side flaps of the comfort padding from the cavity betwe-
en the inner polystyrene cheek pads and the outer shell (Fig. 16).
11.5. Remove the chin straps from the liner (Fig. 17 A).
11.6. Completely remove the liner from the helmet.
12.
Inner Comfort Padding Assembly
12.1. Insert the liner correctly into the helmet and fit it well against the base.
12.2. Pull the left rectangular textile extension of the liner (Fig. 17 B) and insert the
chin strap into the corresponding slot in the cheek pad area of the liner (Fig. 17
A); then fold the rectangular textile extension of the liner inside the padding.
Follow the same steps on the right side of the helmet.
12.3. Insert the right and left side flaps of the liner pushing them into the cavities bet-
ween the inner polystyrene cheek pads and the outer shell (Fig. 16).
12.4. Insert the left front flap of the liner into its seat on the support fixed to the poly-
styrene inner shell and push it downwards until it is completely locked. Follow
the same steps for the central and right flap (Fig. 15).
NOTE: Check the correct assembly of the liner front area by lifting and lowering
the VPS. These movements should be smooth. If this is not the case, repeat
the steps 11.3 and 12.4.
12.5. Insert the rear right, central and left flaps of the liner into the relevant support
seats in the shell edge (Fig. 14). Push the flaps until they are fully hooked onto
the support.
12.6. Push the padding of the cheek pad in line with the snap fastener on its back by
fastening it to the attachment seat of the frame fixed to the shell (Fig. 13). Whilst
doing this, check that the above mentioned rectangular textile extensions do not
come between the snap fastener and the corresponding fastening seats.
WARNING
-
Remove the inner comfort padding only when cleaning or washing is required.
-
Never use the helmet before completely and correctly reassembling its inner
comfort padding.
-
Delicately hand-wash in lukewarm water (max. 30° C) and neutral soap.
-
Rinse with cold water and allow drying at room temperature, away from direct
sunlight.
-
Never machine-wash the inner comfort padding.
-
The inner polystyrene is an easily deformable material. It is apt to change or get
partially destroyed to help absorb shocks.
-
Do not modify or alter the helmet’s internal polystyrene components in any way.
-
Clean the inner components with a damp cloth only and allow it to dry at room
temperature away from direct sunlight.
-
Never use tools or equipment of any sort to carry out the steps described
above.
20
N40 OK_N104 0072 14/01/14 16.07 Pagina 20
Содержание N40 FULL
