background image

 

 
 

13 

Drive carefully the truck to the destination. Watch  the route conditions  and adjust the travelling speed 

with the accelerator button.   

The truck has vertical driving function. 

With tiller in its vertical position, press turtle button

  (Fig.7, 17) and hold still, move the accelerator 

button to activate driving function and travel slowly, which is suitable for narrow space operation. 

 

e.   Steering 

 

Steer the truck by moving the tiller to the left or right side. 

 

f. Braking 

 

PLEASE CHECK THE BRAKING DISTANCE WITH TRUCK BEFORE OPERATION 

THE  BRAKING  PERFORMANCE  DEPENDS  ON  THE  TRACK  CONDITIONS  AND  THE  LOAD 

CONDITIONS OF THE TRUCK 

 

The braking function can be activated on several ways: 

 

 

By moving the accelerator button (14

) back to the initial ‘0’ position or by releasing the button, the 

regenerative braking is activated. The truck brakes until it stops. 

 

By moving the accelerator button (14) from one driving direction directly to the opposite direction, 

the truck brakes regenerative until it starts traveling into the opposite direction. 

 

The truck 

brakes, if the tiller is moved up or down to the braking zones (‘B’). If the tiller is released, 

the tiller moves automatically up to the upper baking zone (‘B’).The truck brakes until it stops.

 

 

The safety (belly) button (1) prevents the operator from being crushed. If this button is activated, the 
truck decelerates and/ or starts traveling into the backwards direction (‘Bw.’) for a short distance and 

stops. Please consider, that this button also operates, if the truck is not traveling and the tiller is in 

the operating zone.

 

 

g.   Malfunctions 

If  there  are  any  malfunctions  or  the  truck  is  inoperative,  please  stop  using  the  truck  and  activate  the 

emergency  button  (5)  by  pushing  it.  If  necessary,  tow  the  truck  out  of  the  operating  area  by  using 

dedicated towing/ lifting equipment. 

 

h. 

 

Emergency

 

In emergencies or in the event of tip over (or off dock), keep safe distance immediately. If possible push 

the emergency button (5). All electrical functions will be stopped. 

 

Release button

to cancel vertical driving

Содержание PTE15-C


























Отзывы: