Nittan EVA-PYH Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 26

background image

DW1401831 Rev.K1

Sep 18, 2015

22

Section 10 - MAINTENANCE

Notes

:

•

Before cleaning, notify the proper authorities that the system is undergoing maintenance, and therefore the

system will temporarily be out of service.

•

Disable the loop or system undergoing maintenance to prevent unwanted alarms.

It is recommended that the sensor be removed from its mounting base for easier cleaning and that sensors be cleaned
at least once a year.

Do not disassemble, repair, or modify the products. It may cause a fire or electric shock.

! CAUTION

1.

Carefully remove the detector head from its base.

2.

Use a soft, lint-free cloth, moistened with alcohol for sticky deposits, to clean the plastic enclosure.

3.

Using a soft bristle brush (e.g. an artist’s paint

-brush) carefully brush around the thermistor, avoiding touching the

thermistor and photo chamber.

4.

Ensure that no debris remains on or around the thermistor or photo chamber once cleaning is complete.
If the unit needs further cleaning, or is damaged or corroded, please return the complete detector to NITTAN
COMPANY, LIMITED for warranty service.

5.

Reinstall the detector.

6.

Test the detector according to Section 9 - TESTING.

7.

Set the system back to normal operation mode.

8.

Notify the proper authorities that the system is back on line.

«
...
20
21
22
23
24
...
»

Содержание EVA-PYH



























Отзывы:

Нет отзывов

Похожие инструкции для EVA-PYH

Бренд: Ole Hickory Pits Страницы: 44

Бренд: Steelmate Страницы: 16

Бренд: Autostart Страницы: 9

Бренд: oklahoma joes Страницы: 16

Set & Forget 19956

Бренд: ACU-RITE Страницы: 12

Бренд: Anka Страницы: 8

Бренд: Sharper Image Страницы: 4

Бренд: Sharper Image Страницы: 6

Бренд: Sharper Image Страницы: 28

Бренд: Firex Страницы: 8

Бренд: System Sensor Страницы: 17

Бренд: System Sensor Страницы: 21

Platinum APS-787a

Бренд: Prestige Страницы: 24

Бренд: Hark Страницы: 25

Бренд: Directed Electronics Страницы: 21

Бренд: Directed Electronics Страницы: 24

Бренд: Punkt Страницы: 4

Бренд: Eurotops Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды