Nittan EVA-PYH Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 26

background image

DW1401831 Rev.K1

Sep 18, 2015

17

8.4

Procedure for installing

Note:

All wiring must be installed in compliance with the National Electrical Code, applicable local codes and the

Authority Having Jurisdiction.

Proper wire gauges should be used. The installation wires should be color coded to limit wiring mistakes and ease

system troubleshooting. Improper connections will prevent a system from responding properly in the event of a fire.

Remove power from the communication line before installing detectors.

1. Pass the field wiring through the rear center cable opening in the mounting base. Install the base to the electrical

box with screws via the base mounting holes. Connect the field wiring to the base terminals, as detailed in Figure
18. Do not use looped wire under terminals (See Figure 19).

2. Using the EVA-AD2 Address Programmer, set the desired address for each detector. See Annex A for the

handling.

3. Install the detector into the mounting base,

making sure the wiring does not obstruct mounting of the detector head.

Push the detector into the mounting base while turning it clockwise until the detector locks into place. Use a small
hexagonal wrench to set the tamper resist feature (if required), see Figure 20.

4. After the detector has been installed, snap on the supplied plastic dust cover onto the detector to keep out dust during

construction.

5. Apply power to the control panel to configure the detectors to the fire alarm control panel.

6.

Test the detector(s) as described in the TESTING section of this manual.

After commissioning has been completed remove and discard the dust cover.

! CAUTION

Smoke and heat detectors are not to be used with detector guards unless the
combination has been evaluated and found suitable for that purpose.

! CAUTION

Notes:

•

If the dust cover is not used while construction work is being completed, exposure to a slightly dusty

environment can cause unwanted alarms after the commissioning the detectors.

•

In the event of an unwanted alarm after commissioning clean the detector and re-install.

•

If the detector still produces unwanted alarms replace the detector.

«
...
15
16
17
18
19
...
»

Содержание EVA-PYH



























Отзывы:

Нет отзывов

Похожие инструкции для EVA-PYH

INSAFE+Origin D731D

Бренд: Nexelec Страницы: 34

EVO ONE THAR-ONE-KHY2

Бренд: Fortin Страницы: 8

Бренд: Honeywell Страницы: 4

Бренд: Prestige Страницы: 20

Бренд: Masterbuilt Страницы: 30

Бренд: Fire-Lite Alarms Страницы: 2

Moondance Glow M402SR

Бренд: Altec Lansing Страницы: 28

Бренд: CrimeStopper Страницы: 7

Бренд: Fusion Страницы: 9

Бренд: La Crosse Страницы: 2

Бренд: La Crosse Страницы: 10

Бренд: Eleven Twelve Страницы: 16

Бренд: Firex Страницы: 2

Бренд: Hark Страницы: 23

Бренд: La Crosse Technology Страницы: 11

Бренд: Code Alarm Страницы: 8

Бренд: Code Alarm Страницы: 13

Бренд: Code Alarm Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды