Ninja H5, Руководство пользователя

Страница: 19 / 35

5 6 www.ninja.com.cn
English
Chapter I: Safety Precautions Chapter I: Safety Precautions
Attention:
Pay attention to the risk of human injury or item damage.
Attention:
Pay attention to the risk of human injury or item damage.
11 No empty load (no food in the cup) or
overload (food amount is above the
rated amount) when using the product
(Figure 1)
12
The speed and time adjustment function
of this product is only applicable for DIY
recipes.
13
Before turning the power on, make sure
the switch is off, and the cup and oth-
er parts have been installed in place to
avoid a dead machine or causing per-
sonal injury.
14
Turn off the machine and disconnect the
power supply before changing parts or
contacting moving parts.
15
When the product is working, it is strictly
forbidden to move the product, raise the
cup or touch the blade, motor and other
movable parts to avoid human injury or
damage to the product.
16
Before disassembling, assembling, ad-
justing or cleaning any part of the prod-
uct, turn off the switch and disconnect
the power supply to avoid electric leak-
age or accidental activation of the ma-
chine.
17 When the machine is working, it is strict-
ly forbidden to open the lid and add
food to avoid spattering and scalding.
Open the feeding cover in middle of the
lid to add food through the feeding hole.
(Figure 2)
18
It is strictly prohibited to use the stir-
ring rod directly inside the cup in case
any damage to the blade and motor or
any accident. Open the feeding cover in
middle of the lid to insert the stirring rod
through the feeding hole. (Figure 3)
19 Stir for no more 6 minutes (Refer to rec-
ipe instructions and screen indication
for the running time of each program),
stop for 1 minute afterwards, this is one
stirring cycle. After 3 consecutive cy-
cles, the machine must be turned off and
cooled for 15 minutes in order to ensure
product life.
20
The machine’s continuous heating time
shall not exceed 90 minutes. DIY heating
can last up to 4 hours. If the power is off
when making hot drinks, change ingre-
dients to restart the preparation process
so that it doesn't get sticky.
21 Any liquid spills during the machine
working process should be cleaned up
timely to avoid liquid spills contacting
the connecting parts.
22
If the blade is stuck, turn off the switch
and disconnect the power supply before
cleaning to avoid any injury accident or
damage to the product.
23 When the preparation process com-
pletes, the machine will prompt 5 "di"
tones. Disconnect the power supply first
and then remove the cup, lid and other
parts in case of accident.
24 If the machine stops working sudden-
ly while running, it could be machine
self-protection activated by motor over-
heating. Disconnect the power supply,
cool for 20 to 30 minutes before use.
25 The machine is controlled by intelligent
chip, intermittent noise of irregular
speed rate of the motor during crushing
is normal.
26
The heating unit of the stainless steel
blending cup (hot cup) is still hot after
using, cool down before cleaning. Wash
the cup and parts that are in contact
with food with water. Be careful of the
sharp blades when emptying the cup
and cleaning the parts to avoid cut (Wear
protective gloves).
27 Do not rinse the handle and the bottom
coupler of the stainless steel blending
cup (hot cup) , in case water gets into
the heating plate to damage the ma-
chine or cause accident.
28 No water is allowed to get into the han-
dle and the bottom coupler of the stain-
less steel blending cup (hot cup) and the
glass blending cup (cold cup); If there is
water, wipe up or dry up before use.
29 Don’t wash or sterilize any part of the
machine in dishwasher, microwave oven,
sterilizing cabinet, or hot water above
60; don’t heat it with other equipment
to prevent component deformation or
damage.
30
Don’t expose the machine in environ-
ments with high temperature, or strong
magnetic, or with flammable and explo-
sive gases (natural gas, biogas, etc.) in
case of malfunction of any part or caus-
ing any accident.
31 Turn off the switch and disconnect the
power supply when no one is using to
prevent short circuit.
32 Hand it over to relevant authorities to
discard the machine or its packages. Cut
the power cord before discarding.
33 The machine will produce a certain level
of mechanical noise when stirring at high
speed, sorry for the disturbance.
Figure 2 Figure 3
Keep this Operation
Manual safely
下厂文件 V1-190103