Nilfisk-Advance SC350 Скачать руководство пользователя страница 6

Страница: 6 / 26

GENERAL INFORMATION

ENGLISH

SERVICE MANUAL

9098840000

SC350

GENERAL INSTRUCTIONS

Specific warnings and cautions to inform about potential damages to people and machine are shown below.

DANGER!

Before performing any machine maintenance, repair, cleaning or replacement procedure, disconnect the

–

battery connector and turn the main switch to “0”.

This machine must be used by properly trained operators only.

–

Keep the battery away from sparks, flames and incandescent material. During the normal operation explosive

–

gases are released.

Do not wear jewels when working near electrical components.

–

Do not work under the lifted machine without supporting it with safety stands.

–

Do not operate the machine near toxic, dangerous, flammable and/or explosive powders, liquids or vapours:

–

This machine is not suitable for collecting dangerous powders.

Battery charging produces highly explosive hydrogen gas. Keep the cover open during battery charging and

–

perform this procedure in well-ventilated areas and away from naked flames.

WARNING!

Carefully read all the instructions before performing any maintenance/repair procedure.

–

Before using the battery charger, ensure that frequency and voltage values, indicated on the machine serial

–

number plate, match the electrical mains voltage.

Do not pull or carry the machine by the battery charger cable and never use the battery charger cable as

–

a handle. Do not close a door on the battery charger cable, or pull the battery charger cable around sharp

edges or corners. Do not run the machine on the battery charger cable.

Keep the battery charger cable away from heated surfaces.

–

Do not use the machine if the battery charger cable or plug is damaged. If the machine is not working as it

–

should, has been damaged, left outdoors or dropped into water, return it to the Service Center.

To reduce the risk of fire, electric shock, or injury, do not leave the machine unattended when it is plugged

–

in. Before performing any maintenance procedure, disconnect the battery charger cable from the electrical

mains.

Do not smoke while charging the battery.

–

Содержание SC350



























Результаты поиска

Содержание SC350

Отзывы:

Похожие инструкции для SC350

Бренды по названию

Популярные бренды

Nilfisk-Advance SC350, Руководство по обслуживанию

Результаты поиска

Содержание SC350

Отзывы:

Похожие инструкции для SC350

Бренды по названию

Популярные бренды