background image

GENERAL INFORMATION

SERVICE MANUAL

ENGLISH

SC350

9098840000

5

WARNING!

Always protect the machine against the sun, rain and bad weather, both under operation and inactivity 

 

condition. Store the machine indoors, in a dry place: This machine must be used in dry conditions, it must 

not be used or kept outdoors in wet conditions.

Before using the machine, close all doors and/or covers as shown in the User Manual.

 

Do not allow to be used as a toy. Close attention is necessary when used near children.

 

Use only as shown in this Manual. Use only Nilfisk’s recommended accessories.

 

Take all necessary precautions to prevent hair, jewels and loose clothes from being caught by the machine 

 

moving parts.

Pay attention to the machine moving parts. When using the machine, the deck can abruptly turn by 180°.

 

Do not use the machine on incline.

 

Do not tilt the machine more than the angle indicated on the machine itself, in order to prevent instability.

 

Do not use the machine in particularly dusty areas.

 

Use the machine only where a proper lighting is provided. 

 

While using this machine, take care not to cause damage to people or objects.

 

Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects.

 

Do not lean liquid containers on the machine, use the relevant can holder.

 

The machine working temperature must be between 0°C and +40°C.

 

The machine storage temperature must be between 0°C and +40°C.

 

The humidity must be between 30% and 95%.

 

When using floor cleaning detergents, follow the instructions on the labels of the detergent bottles. 

 

To handle floor cleaning detergents, wear suitable gloves and protections. 

 

Do not allow the brushes to operate while the machine is stationary to avoid damaging the floor.

 

In case of fire, use a powder fire extinguisher, not a water one.

 

Do not tamper with the machine safety guards and follow the ordinary maintenance instructions 

 

scrupulously.

Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged. 

 

Always keep the openings free from dust, hairs and any other foreign material which could reduce the air 

flow. 

Do not remove or modify the plates affixed to the machine.

 

This machine cannot be used on roads or public streets.

 

Pay attention during machine transportation when temperature is below freezing point. The water in the 

 

recovery tank or in the hoses could freeze and seriously damage the machine.

Use brushes and pads supplied with the machine and those specified in the User Manual. Using other 

 

brushes or pads could reduce safety.

In case of machine malfunctions, ensure that these are not due to lack of maintenance. Otherwise, request 

 

assistance from the authorised personnel or from an authorised Service Center.

If parts must be replaced, require ORIGINAL spare parts from an Authorised Dealer or Retailer.

 

To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of 

 

this Manual, must be performed by the authorised personnel or by an authorised Service Center.

Do not wash the machine with direct or pressurised water jets, or with corrosive substances. 

 

The machine must be disposed of properly, because of the presence of toxic-harmful materials (battery, etc.), 

 

which are subject to standards that require disposal in special centres (see Scrapping chapter on the User 

Manual).

Содержание SC350



























Отзывы: