Nikon AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED Скачать руководство пользователя страница 73

Страница: 73 / 98

JAA79651-R.3695.A

- Ａ52 ･ AF-S DX 18-135/3.5-5.6G -

④

Turn the power of viewers (5 pcs.) to ON.

(Note: If the batteries of viewers are exhausted with decreased brightness, the shooting data cannot
be obtained correctly.)

Viewer× 5 pcs.

⑤

Fit the lens to be examined in the camera (D100). Set the zoom to (70 mm) and rotate the focus ring to focus

on the chart.

⑥

By looking through the viewfinder, adjust the height and tilt to make the chart fill the entire finder field

frame.

⑦

Adjust the tilt of the slide rail to make the three chart lines position in the center of the viewfinder, when the

tripod is slid all the way to the front and back.

Front

Back

⑧

Connect the PC and camera via USB cable. (Camera setting: Mass Storage

）

⑨

Start the adjustment software (LWM.exe).

⑩

"Lens Select" window opens. Select "AFS 18-135/3.5-5.6G", then click "OK" button.

⑪

Click the "Reset all log" button.

Содержание AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED



































































































Результаты поиска

Содержание AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Отзывы:

Похожие инструкции для AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Бренды по названию

Популярные бренды

Nikon AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED, Руководство по ремонту

Результаты поиска

Содержание AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Отзывы:

Похожие инструкции для AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Бренды по названию

Популярные бренды